Traxxas Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive equipment that fits several Traxxas
automobiles. .
Suches as: 1 equipment just

Frequently bought with the product that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Here is another product that compliments the product being gone over.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building and construction

SUCHES AS:
One steel 30T idler equipment

NEEDS:
Setup on automobile

The listed below product also pairs really well with the product being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This product compliments the main item below.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

This product is frequently bought with the above pointed out product.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

SUCHES AS:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the automobile

REMARKS:
For primary differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037

You will love this product if you have the product above mentioned.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

SUCHES AS:
One gearbox
One idler shaft

REMARKS:
This part fit the requirement and XL version of both the Stampede
and Rustler.

Numerous others have actually bought this product in addition to the product that you are presently reading about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

SUCHES AS:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

Frequently bought with the product that you are presently reading about.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This product is frequently bought with the above pointed out product.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for models with a slipper clutch.
Black plastic building and construction

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).