Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Equipment for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Created for designs with a slipper clutch
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).

Here is a great thing that lots of others have actually purchased the same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

You will certainly like this thing if you have the thing earlier pointed out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly like this thing if you have the thing earlier pointed out.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal building and construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Equipment
One Set Screw

NEEDS:
Setup

Many others have actually bought this thing along with the thing that you are currently reading about.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Equipment from Traxxas.

FEATURES:
Steel building and construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Equipment with set screw

NEEDS:
Installing on motor shaft

SPECS:
Variety of Pearly whites: 16T
Pitch: 48
Inner Diameter: 0.12" (3mm)

Here is a great thing that lots of others have actually purchased the same time.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Equipment for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Created for designs with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 83

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Here is another thing that compliments the thing being discussed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Here is another thing that compliments the thing being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

NEEDS:
Disassembly of slipper clutch

This thing compliments the above discussed thing.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Automobile