Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Created for models with a slipper clutch
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).

Right here is a fantastic thing that lots of others have actually bought at the exact same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

You will certainly like this item if you have the item just above pointed out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly like this item if you have the item just above pointed out.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal building and construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Gear
One Set Screw

REQUIRES:
Installation

Numerous others have actually purchased this thing in addition to the thing that you are presently reviewing.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Gear from Traxxas.

FEATURES:
Steel building and construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Gear with set screw

REQUIRES:
Setting up on motor shaft

SPECS:
Variety of Pearly whites: 16T
Pitch: 48
Inner Diameter: 0.12" (3mm)

Right here is a fantastic thing that lots of others have actually bought at the exact same time.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Created for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 83

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Right here is another thing that compliments the thing being reviewed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Right here is another thing that compliments the thing being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

This thing compliments the above reviewed thing.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Automobile