Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Designed for models with a slipper clutch
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).

Below is a fantastic thing that numerous others have actually bought at the very same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Designed for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

You will certainly love this item if you have the item just above stated.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this item if you have the item just above stated.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal building and construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Gear
One Set Screw

REQUIRES:
Setup

Lots of others have actually purchased this thing together with the thing that you are presently checking out.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Gear from Traxxas.

FEATURES:
Steel building and construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Gear with set screw

REQUIRES:
Setting up on motor shaft

SPECS:
Number of Pearly whites: 16T
Pitch: 48
Inner Diameter: 0.12" (3mm)

Below is a fantastic thing that numerous others have actually bought at the very same time.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Designed for models with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 83

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Below is one more thing that praises the thing being discussed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Below is one more thing that praises the thing being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

This thing praises the above discussed thing.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Vehicle