Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Equipment for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Created for designs with a slipper clutch
Black plastic construction

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).

Here is a excellent thing that numerous others have purchased the same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

You will enjoy this product if you have the product just above discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will enjoy this product if you have the product just above discussed.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Equipment
One Set Screw

NEEDS:
Setup

Many others have gotten this thing in addition to the thing that you are presently reading about.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Equipment from Traxxas.

FEATURES:
Steel construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Equipment with set screw

NEEDS:
Installing on motor shaft

SPECIFICATIONS:
Variety of Teeth: 16T
Pitch: 48
Inner Diameter: 0.12" (3mm)

Here is a excellent thing that numerous others have purchased the same time.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Equipment for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Created for designs with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Here is an additional thing that praises the thing being reviewed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Here is an additional thing that praises the thing being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

This thing praises the above reviewed thing.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Vehicle