Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Equipment for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Designed for models with a slipper clutch
Black plastic construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Below is a excellent item that numerous others have bought at the very same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Designed for models with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

You will enjoy this thing if you have the thing earlier discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will enjoy this thing if you have the thing earlier discussed.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Equipment
One Set Screw

REQUIRES:
Setup

Lots of others have purchased this item along with the item that you are presently reading about.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Equipment from Traxxas.

FEATURES:
Steel construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Equipment with set screw

REQUIRES:
Installing on motor shaft

SPECS:
Variety of Teeth: 16T
Pitch: 48
Inner Diameter: 0.12" (3mm)

Below is a excellent item that numerous others have bought at the very same time.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Designed for models with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    86T gear (TRAC4686) and 90T gear (TRAC4690).

Below is an additional item that compliments the item being reviewed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

Below is an additional item that compliments the item being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

REQUIRES:
Disassembly of slipper clutch

This item compliments the above reviewed item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Car