Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for models
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Developed for models with a slipper clutch
Black plastic construction

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).

Below is a wonderful thing that lots of others have purchased the very same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for models with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for models with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

You will love this item if you have the item above mentioned.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will love this item if you have the item above mentioned.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Gear
One Set Screw

NEEDS:
Installation

Numerous others have gotten this thing along with the thing that you are presently reviewing.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Gear from Traxxas.

FEATURES:
Steel construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Gear with set screw

NEEDS:
Installing on motor shaft

SPECIFICATIONS:
Number of Pearly whites: 16T
Pitch: 48
Inner Diameter: 0.12" (3mm)

Below is a wonderful thing that lots of others have purchased the very same time.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for models with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 83

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Below is an additional thing that compliments the thing being reviewed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Below is an additional thing that compliments the thing being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

NEEDS:
Disassembly of slipper clutch

This thing compliments the above reviewed thing.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Automobile