Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Equipment for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for designs with a slipper clutch.
Black plastic building

INCLUDES:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is likewise a 86T gear (TRAC4686),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

This is a great enhancement to the item presently being talked about.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Equipment for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for designs with a slipper clutch.
Black plastic building

INCLUDES:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    86T gear (TRAC4686) and 90T gear (TRAC4690).

Get this item to boost the one you are reading around.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Equipment with Set Screw
from Traxxas.

FEATURES:
Steel building, silver in color

INCLUDES:
One 31 Tooth, 48 Pitch Pinion Equipment
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Setup

SPECIFICATIONS:
Length: .42" (10.5mm)
Inside Diameter: 1/8"
Outdoors Diameter: .69" (17.5mm)

Lots of others have actually purchased this item together with the item that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Below is another item that compliments the item being talked about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

INCLUDES:
One Steel Disc
Two Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Get this item to boost the one you are reading around.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want another wonderful item to compliment the above stated item?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
6 black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These may likewise be referred to as coverplate screws.

This item is often purchased with the above stated item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Automobile

This item compliments the above talked about item.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Just (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube required)
Wide surface area, gold-plated terminals
Reverse polarity security makes it impossible to link in reverse
Textured surface for easy gripping
Suitable with high-current 12-gauge wire
Protect, positive locking spring loaded terminals for consistent
    contact
Multiple locking barbs keep terminals secure

INCLUDES:
Two black female plastic connectors
Two sets of gold metal pins
Direction sheet

REQUIRES:
Soldering wires to the metal pins