Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for models with a slipper clutch.
Black plastic building

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is likewise a 86T equipment (TRAC4686),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

This is a great addition to the product currently being reviewed.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Gear for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for models with a slipper clutch.
Black plastic building

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Get this product to improve the one you are reading about.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Gear with Set Screw
from Traxxas.

FEATURES:
Steel building, silver in color

SUCHES AS:
One 31 Tooth, 48 Pitch Pinion Gear
One 3x4mm Set Screw (1.5mm hex size)

NEEDS:
Setup

SPECIFICATIONS:
Length: .42" (10.5mm)
Inside Diameter: 1/8"
Outdoors Diameter: .69" (17.5mm)

Numerous others have bought this product along with the product that you are currently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Below is another product that praises the product being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

SUCHES AS:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

NEEDS:
Disassembly of slipper clutch

Get this product to improve the one you are reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want another great product to enhance the above discussed product?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These might likewise be referred to as coverplate screws.

This product is regularly bought with the above discussed product.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

SUCHES AS:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Car

This product praises the above reviewed product.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Just (No Wires).

FEATURES:
Shrouded wire connections (no shrink tube needed)
Wide surface area, gold-plated terminals
Reverse polarity protection makes it impossible to connect backwards
Textured surface area for simple gripping
Compatible with high-current 12-gauge wire
Secure, favorable locking spring packed terminals for consistent
    contact
Several locking barbs keep terminals secure

SUCHES AS:
Two black female plastic connectors
Two sets of gold metal pins
Instruction sheet

NEEDS:
Soldering wires to the metal pins