Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for models with a slipper clutch.
Black plastic construction

INCLUDES:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 76

REMARKS:
For this slipper clutch design there is likewise a 86T gear (TRAC4686),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

This is a superb addition to the item presently being reviewed.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for models with a slipper clutch.
Black plastic construction

INCLUDES:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 83

REMARKS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    86T gear (TRAC4686) and 90T gear (TRAC4690).

Get this item to improve the one you are reading about.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Equipment with Set Screw
from Traxxas.

FEATURES:
Steel construction, silver in color

INCLUDES:
One 31 Tooth, 48 Pitch Pinion Equipment
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Installation

SPECIFICATIONS:
Length: .42" (10.5mm)
Inside Size: 1/8"
Outdoors Size: .69" (17.5mm)

Numerous others have actually bought this item along with the item that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Below is an additional item that compliments the item being reviewed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

Get this item to improve the one you are reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional wonderful item to match the above mentioned item?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
6 black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Size: 3mm

REMARKS:
These may likewise be described as coverplate screws.

This item is frequently bought with the above mentioned item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Car

This item compliments the above reviewed item.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Only (No Wires).

FUNCTIONS:
Shrouded wire connections (no diminish tube needed)
Wide surface area, gold-plated terminals
Reverse polarity security makes it impossible to link backwards
Textured surface area for easy gripping
Suitable with high-current 12-gauge wire
Protect, positive locking spring packed terminals for constant
    contact
Multiple locking barbs keep terminals protect

INCLUDES:
Two black female plastic adapters
Two sets of gold metal pins
Guideline sheet

REQUIRES:
Soldering wires to the metal pins