Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for models with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is likewise a 86T gear (TRAC4686),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

This is a wonderful enhancement to the item presently being discussed.

Spur Gear (83T) 48P

This is a 48P, 83T Stimulate Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for models with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    86T gear (TRAC4686) and 90T gear (TRAC4690).

Get this item to improve the one you read about.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Equipment with Set Screw
from Traxxas.

FEATURES:
Steel building, silver in color

CONSISTS OF:
One 31 Tooth, 48 Pitch Pinion Equipment
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Setup

SPECS:
Length: .42" (10.5mm)
Inside Size: 1/8"
Outside Size: .69" (17.5mm)

Lots of others have acquired this item together with the item that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

Below is an additional item that compliments the item being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Get this item to improve the one you read about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional great item to compliment the above mentioned item?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Size: 3mm

COMMENTS:
These may likewise be referred to as coverplate screws.

This item is regularly acquired with the above mentioned item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Vehicle

This item compliments the above discussed item.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Only (No Wires).

FEATURES:
Shrouded wire connections (no shrink tube needed)
Wide surface area, gold-plated terminals
Reverse polarity defense makes it impossible to link backwards
Textured surface area for easy gripping
Suitable with high-current 12-gauge wire
Protect, favorable locking spring packed terminals for constant
    contact
Several locking barbs keep terminals protect

CONSISTS OF:
2 black female plastic connectors
2 sets of gold metal pins
Guideline sheet

REQUIRES:
Soldering wires to the metal pins