Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for models with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is also a 86T equipment (TRAC4686),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

This is a fantastic addition to the thing presently being talked about.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Equipment for models with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for models with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Get this thing to improve the one you are reading about.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Equipment with Set Screw
from Traxxas.

FEATURES:
Steel building, silver in color

CONSISTS OF:
One 31 Tooth, 48 Pitch Pinion Equipment
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Installation

SPECS:
Length: .42" (10.5mm)
Inside Diameter: 1/8"
Outside Diameter: .69" (17.5mm)

Numerous others have actually gotten this thing together with the thing that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Below is an additional thing that compliments the thing being talked about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
Two Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Get this thing to improve the one you are reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Want an additional terrific thing to enhance the above discussed thing?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
6 black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These may also be described as coverplate screws.

This thing is frequently gotten with the above discussed thing.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Automobile

This thing compliments the above talked about thing.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Only (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube required)
Wide area, gold-plated terminals
Reverse polarity security makes it difficult to link in reverse
Textured surface area for simple gripping
Compatible with high-current 12-gauge wire
Protect, positive locking spring crammed terminals for constant
    contact
Several locking barbs keep terminals protect

CONSISTS OF:
2 black female plastic adapters
2 sets of gold metal pins
Guideline sheet

REQUIRES:
Soldering wires to the metal pins