Traxxas Spur Gear (76T) 48P

This is a 48P, 76T Spur Gear for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
76 tooth
Developed for designs with a slipper clutch.
Black plastic construction

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 76

COMMENTS:
For this slipper clutch design there is also a 86T equipment (TRAC4686),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

This is a wonderful addition to the item currently being discussed.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Gear for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for designs with a slipper clutch.
Black plastic construction

SUCHES AS:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 83

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Get this item to boost the one you read around.

31T Pinion 48P

This is a 31 Tooth, 48 Pitch Pinion Gear with Set Screw
from Traxxas.

FEATURES:
Steel construction, silver in color

SUCHES AS:
One 31 Tooth, 48 Pitch Pinion Gear
One 3x4mm Set Screw (1.5mm hex size)

REQUIRES:
Installation

SPECIFICATIONS:
Length: .42" (10.5mm)
Inside Diameter: 1/8"
Outdoors Diameter: .69" (17.5mm)

Several others have actually acquired this item together with the item that you are currently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Right here is another item that praises the item being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

SUCHES AS:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Get this item to boost the one you read around.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

Want another terrific item to compliment the above pointed out item?

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These may also be referred to as coverplate screws.

This item is regularly acquired with the above pointed out item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

SUCHES AS:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Automobile

This item praises the above discussed item.

Traxxas Female Connector Set (2)

These are the Female Traxxas Connectors Plugs Just (No Wires).

FEATURES:
Shrouded wire connections (no diminish tube needed)
Wide area, gold-plated terminals
Reverse polarity security makes it impossible to connect backwards
Textured surface for simple gripping
Compatible with high-current 12-gauge wire
Protect, favorable locking spring loaded terminals for constant
    contact
Numerous locking barbs keep terminals protect

SUCHES AS:
Two black female plastic adapters
Two sets of gold metal pins
Instruction sheet

REQUIRES:
Soldering wires to the metal pins