Traxxas Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Equipment for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Developed for designs with a slipper clutch
Black plastic construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 90

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).

Below is a terrific item that several others have purchased the very same time.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for designs with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

You will like this product if you have the product previously pointed out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will like this product if you have the product previously pointed out.

19T Pinion 48P

This is a Traxxas 19T 48P Pinion Gear.

FEATURES:
Metal construction
Grey in color

CONSISTS OF:
One 19T 48P Pinion Equipment
One Set Screw

REQUIRES:
Installation

Several others have acquired this item along with the item that you are currently reading about.

Pinion Gear 16T 48P W/Screw Set

    This is the 16 Tooth 48 Pitch Pinion Equipment from Traxxas.

FEATURES:
Steel construction

CONSISTS OF:
16 Tooth 48 Pitch Pinion Equipment with set screw

REQUIRES:
Installing on motor shaft

SPECS:
Variety of Pearly whites: 16T
Pitch: 48
Inner Size: 0.12" (3mm)

Below is a terrific item that several others have purchased the very same time.

Spur Gear (83T) 48P

This is a 48P, 83T Spur Equipment for designs with
Traxxas Torque Control Slipper Clutch.

FEATURES:
48 pitch
83 tooth
Developed for designs with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur equipment

SPECS:
Pitch: 48
Tooth: 83

REMARKS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    86T equipment (TRAC4686) and 90T equipment (TRAC4690).

Below is an additional item that praises the item being talked about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

Below is an additional item that praises the item being talked about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

REQUIRES:
Disassembly of slipper clutch

This item praises the above talked about item.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Vehicle