Traxxas Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set contains the spring retainers that hold the springs in
location over the shock body and the piston heads that control the amount
of oil circulation in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for two shocks.
Fits the shocks on most Traxxas nitro and electric powered vehicles.
Two hole piston moving towards higher dampening or three hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    2 upper and two lower spring retainers
    2 2 hole piston head covers
    Two 3 hole piston head covers

NEEDS:
Disassembly of shock to set up parts.

This item is often bought with the above mentioned item.

Wide Front Bumper, For Traxxas Rustler/Stampede/ Nitro Sport/Ban

This is a Wide Front Bumper for the Traxxas Rustler and Stampede.
The Bumper goes on the Front of the Automobile and Safeguards the Chassis.

FEATURES:
Long lasting Plastic Building and construction
Black in Color

CONSISTS OF:
One Bumper
One Group RPM Decal

NEEDS:
Setup onto the Traxxas Rustler or Stampede.

SPECS:
Length: 2-3/4"
Width: 6-1/8"

REMARKS:
The Factory Number is #81162

This item compliments the main item below.

Shoulder Screws Ultra Shocks

These are the Shoulder Screws for the Traxxas T-Maxx 3.3.

FUNCTIONS:
Black steel building and construction

CONSISTS OF:
Six steel shoulder screws

SPECS:
Length: 12mm
Diameter: 3mm

Right here is an additional item that compliments the item being talked about.

Plastic Shock Caps & Bottoms

These are Shock Caps and Bottoms for Traxxas kits.
These seal the shock including the shock oil.

FEATURES:
Nylon building and construction

CONSISTS OF:
2 nylon shock cap (tops)
2 nylon shock cap (bottoms)

NEEDS:
Other shock parts

SPECS:
Diameter Tops Bottoms
16MM 13MM

REMARKS:
These fit the N/E 4-tec, N/E Stampede, and T/E-Maxx

The below item also sets actually well with the item being talked about.

Motor Titan 12T 550 (12-Turns)

    This is the Traxxas Titan 550 12 Turn Electric Motor.

FEATURES:
Stock motor supplied with the Traxxas Stampede and Rustler series
Preinstalled leads, capacitors and connectors

CONSISTS OF:
Traxxas Titan 550 Motor, two capacitors and two leads with connectors

NEEDS:
Installing in automobile

SPECS:
Can Diameter: 1.25" (38mm)
Shaft Diameter: 0.12" (3mm)
Length Consisting of Shaft: 3.2" (81mm)
Length Not Consisting of Shaft: 2.3" (57.5mm)
Specs such as RPM are not provided

Right here is an additional item that compliments the item being talked about.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic building and construction

CONSISTS OF:
One spur gear

SPECS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

Many others have bought this item along with the item that you are presently reading about.

Rod Ends Long & Short

This set of rod ends, balls, and screws is utilized on all however four of Traxxas'
sets. It WILL NOT DEAL WITH: the Sledgehammer, initial Hawk, Cat, or Bullet.

Includes: 4 short rod ends (17mm)
16 long rod ends (19mm)
2 ball screws
18 hollow ball connectors

pcd 01/23/94