Traxxas Slash Big Bore Shocks

This is the optional Big Bore Shock Set for the
2WD Traxxas Slash.
These replace the plastic shocks that come stock with the kit.

FEATURES:
Strong aluminum construction, covered
Anodized black with white springs
Completely put together

CONSISTS OF:
Four fully put together shocks with white springs
Mounting hardware
One bottle of silicone oil

REQUIRES:
Filling shocks with shock oil and putting together onto the model

The listed below thing also sets actually well with the thing being talked about.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Heavy Duty Front/Rear A-Arms
for the Traxxas Slash 4x4.

FEATURES:
Black in color
Plastic constrution

CONSISTS OF:
2 Front/Rear A-Arms

REQUIRES:
Setup at front or rear suspension

SPECIFICATIONS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at largest point
Density: 0.31" (8mm)

REMARKS:
Also offered in Blue (RPMC0705)

This thing praises the main item below.



These are the Pro-Line Back Split Sixer Red Bead-Loc On Black Wheels.

FEATURES:
Fits the rear of the Traxxas Slash
front and rear of the Traxxas Slash 4x4
fornt and rear of the HPI Blitz
Nylon construction
Red in color
Red bead-locs
*KEEP IN MIND* - Pro-Line does NOT advise these for use with brushless
systems

CONSISTS OF:
2 Back Split Sixer Wheels

REQUIRES:
Tires

SPECIFICATIONS:
Outer Size: 2.2" (56mm)
Inner Size: 3.0" (76mm)
Width: 40.5mm (1.6")
Hex: 12mm

You will like this item if you have the item earlier discussed.



This is the DuraTrax Onyx 7.4V 5000mAh 25C Hard Case LiPo Battery
with the Traxxas Plug.

FEATURES:
Suitable for 1/10 scale automobile applications
Prewired with Traxxas high present connector

CONSISTS OF:
7.4V 5000mAh 25C Hard Case LiPo Battery with Traxxas Plug

REQUIRES:
Balancer and LiPo suitable charger or LiPo charger with built-in
    balancer such as the Onyx 235, DTXP4235

SPECIFICATIONS:
Voltage Rating: 7.4V
Rated Capacity: 5000mAh
Discharge Rating: 25C continuous
Measurements: 1.77 x .94 x 5.4" (45 x 24 x 137mm)
Weight: 10.2oz (288g)
Discharge Lead/Connectors: 12AWG Wires, Traxxas Plug
Stabilizing Port: ElectriFly
Watt Hours: 37Wh

REMARKS:
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER allow to Discharge listed below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any method or leak cells
NEVER put on combustible products or leave unattended during
    charging
ALWAYS Charge in a fireproof location
ALWAYS set charger's output volts to match battery volts
ALWAYS keep out of reach of children
All weights include wire leads and plugs
All weights +/- 1 g

The listed below thing also sets actually well with the thing being talked about.

Rear Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the RPM Back Shock Tower for the
Traxxas E-Stampede, E-Rustler and E-Bandit.

FEATURES:
Tough nylon enhanced plastic construction
Uses all stock hardware (for installing shocks etc.)

CONSISTS OF:
One rear shock tower

SPECIFICATIONS:
Width: 4.33" (110mm)
Height: 2.75" (70mm)
Density: 7mm