Traxxas Slash 4X4 Body

This is the Brief Course Racing Truck Clear Body
for the Traxxas 4x4 Slash and Slayer.

FEATURES:
Cut and prepared to paint
Clear protective finish on beyond body

SUCHES AS:
Clear Brief Course Racing Truck Body with Window Masks, Sponsor and
    Body Trim Decals

REQUIRES:
Spray or brush-on polycarbonate safe paint

SPECIFICATIONS:
Length: 21.25" (540mm)
Width: 11.5" (292mm)
Height: 5.5" (140mm)

Often bought with the thing that you are presently reading about.



Below is an additional thing that praises the thing being gone over.



This thing praises the above gone over thing.



Often bought with the thing that you are presently reading about.

Ez-Peak Plus Plus 100 Watt Nimh/Lipo Dual Charger W/ Id System

This is the AC Powered Traxxas EZ-Peak 100W Double Battery Charger
with iD Automobile Battery Identification.

FEATURES:
Charges 2S and 3S LiPo batteries
5-8 cell NiMH batteries
Traxxas's iD innovation immediately configures and enhances charge
    settings for Traxxas iD equipped batteries
Charges two batteries simultaneously at as much as 50W (4 amps) each, or
    charges single battery at 100W (8 amp) output in High-Output
    mode
Charges a NiMH and LiPo at the exact same time
Advanced Mode for complete manual control of battery charger settings
Development bar and audible notifies
Storage Mode prepares LiPo batteries for extended storage
30 day restricted service warranty through Traxxas starting at date of
    purchase

SUCHES AS:
Traxxas EZ-Peak 100W Double Battery Charger with AC Power Cable,
    Instructions, Cooling Fan

SPECIFICATIONS:
Input Power: 100-240V/50-60Hz
Output: 100W max
Charge Current: 1-4A (double mode), 5-8A (high output mode)
Discharge Current Variety: 500mA
Existing Drain for Balance Ports: 500mA
Weight: 20.3oz (575g)
Dimensions: 7 x 5.4 x 2.2" (176 x 138 x 57mm)

The below thing additionally sets actually well with the thing being gone over.

Pinion Gear, Differential (Front), X-Maxx

This is the Pinion Gear for the Front Differential
for the Traxxas X-Maxx Beast Truck, TRAD75**.

FEATURES:
Hardened steel building

SUCHES AS:
Pinion Gear for the Front Differential

This is a wonderful addition to the thing presently being gone over.

Pinion Gear, Differential (Rear), X-Maxx

This is the Pinion Gear for the Back Differential
for the Traxxas X-Maxx Beast Truck, TRAD75**.

FEATURES:
Hardened steel building

SUCHES AS:
Pinion Gear for Back Differential

Lots of others have bought this thing along with the thing that you are presently reading about.



This is the 2.4GHz radio controlled, electric powered, prepared to run, Traxxas
Slash Short Course Race Truck.

**The consisted of TQ 2.4GHz radio system is compatible only with the**
**#6519 receiver and does DECLINE the Docking Base accessory.**

FEATURES:
Chassis: Modified tub 0.08" (2mm) thick composite nylon with side
    nerf bars to impact and support body
Drive: Rear wheel
Motor: Titan 12 turn 550 size customized with internal cooling fan
Battery: 7-cell 3000mAh NiMH with Traxxas HD port, and iD
    Automobile Battery Recognition that allows Traxxas iD equipped
    battery chargers to immediately set and optimize charge settings
Battery Charger: 4A DC powered fast battery charger
Transmission: Brushless prepared Magnum 272 metal-gear with ball
    bearings
Slipper Clutch: Revo-spec Torque-Control system
Differential: Planetary type with hardened steel gears
Ball Bearings: Rubber sealed
Main Gear: Plastic, 48 pitch 86 tooth
Pinion Gear: Metal, 48 pitch 18 tooth
Radio: Traxxas TQ 2.4GHz high output with Traxxas Link automated
    model recognition, 3-ch receiver
Radio Box: Sealed and watertight for driving through water, mud, and
    snow
Electronic Speed Control: Traxxas XL-5 watertight, with reverse and
    brake, and Traxxas high present port
Shocks: Adjustable Ultra shocks with X-ring innovation, oil-filled
    plastic body
Wheels: 1.5" (38mm) large, 2.2" (56mm) diameter 5-spoke satin finish
Tires: All terrain with foam inserts 1.8" (46mm) large, 4.25" (108mm)
    outer diameter
Bumpers: Scale front and rear tube design
Body: Formed from Lexan, trimmed and prepainted
Suspension: Four wheel independent
Caster: Adjustable, caster/toe-in describes the angle of the front
    suspension when seen from the side of the vehicle in relation
    to the chassis
Camber: Adjustable, camber describes the angle of the tops of the
    tires from vertical when seen from front or behind car

SUCHES AS:
Traxxas Slash Short Course Race Truck w/TQ 2.4GHz radio system, ESC,
    body, motor, 7-cell 3000mAh NiMH battery, DC powered battery charger,
    decals and showed instruction manual

REQUIRES:
AA Batteries: Four for transmitter
Track equipment

SPECIFICATIONS:
Car-
Length: 22.36" (568mm)
Width: 11.65" (296mm)
Height: 8.42" (214mm)
Front and Rear Track: 11.65" (296mm) distance in between outer edges
    of wheels
Wheelbase: 13.2" (335mm)
Ground Clearance: 3.5" (89mm)
Weight: 76.2oz (2.16kg)
    Body-
Length: 21.3" (542mm)
Width: 11.4" (289mm)
Height: 5.3" (135mm)
Height: 5.3" (135mm)

COMMENTS:
Available in the following color combinations;
    Blue #1 TRAD47BB
    Blue & Orange #25, TRAD47BN, Arie Luyendyk Jr.
    Blue & Red, TRAD47BR
    Pink, TRAD47KK
    Black & Red #9, TRAD47LR, Chad Hord
    Orange #7, TRAD47NN, Robbie Gordon
    Red & Black #25, TRAD47RL, Mark Jenkins

Though the Traxxas Slash is readily available in race reproduction versions
with formally licensed ProGraphix painted bodies, we are not able to
honor specific requests.

The ball bearings in the Traxxas Slash 2WD are rubber closed.
Following are the stock numbers for the replacement bearings from
Traxxas and non-rubber sealed alternatives from Duratrax;
    Qty. Size Place Qty Bearing Set Qty Bearing Set
4 5x11mm Steering Obstructs 2 DTXC1547 2 TRAC5116
4 5x8mm Bellcrank 2 DTXC1523 2 TRAC6728
4 5x11mm R Stub Axles 2 DTXC1547 2 TRAC5116
1 5x11mm Spur Gear 1 DTXC1547 1 TRAC5116
4 5x11mm Transmission 2 DTXC1547 2 TRAC5116