Traxxas Shrt Rod Ends/Ball Cnnctr (6)

This are Rod Ends Short for the Nitro T-Maxx.
These rods ends connect to turnbuckles for front/rear.

FEATURES:
Black nylon rod ends
Steel pivot balls

INCLUDES:
Six nylon rod ends
Six pivot balls

NEEDS:
Turnbuckles: TRAC6338

SPECS:
Length: .695" (17.6mm)
Inner Diameter: .217" (5.5mm)

COMMENTS:
Will work only for the Nitro T-Maxx.

This is a amazing addition to the product presently being reviewed.

3 X 15Mm Button Hex Screw (6)

This is a bundle of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel construction, Black in color
Utilized on the Traxxas Revo beast truck, can likewise be used in any
    application where a 3x15mm button head screw is needed

INCLUDES:
Six 3x15mm Traxxas Button Head Screws

NEEDS:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Diameter: 3mm

Numerous others have bought this product together with the product that you are presently reading about.

Antenna Tube W/ Cap, Black

This is a conventional replacement Antenna Tube with Cap from Dubro
This item can be used anywhere an antenna tube is required to support
a receiver antenna wire.

FEATURES:
Black plastic construction

INCLUDES:
One antenna tube
One antenna tube cap
One receiver antenna wire sleeve

NEEDS:
Absolutely nothing. This is a direct fit part for any boat, vehicle, etc. that uses
    a conventional size antenna tube.

SPECS:
Length: 12 1/4" (311mm)
Diameter: 1/8" (3.2mm)

You will certainly love this item if you have the item earlier discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

Here is a terrific product that lots of others have purchased the very same time.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building and construction

INCLUDES:
One Tie Bar

NEEDS:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

COMMENTS:
None

Want an additional terrific product to compliment the above discussed product?

Rod Ends/Ball Connector (6)

These are 5.8mm ball ends and balls use in the LS II race truck kit.

Kit includes: 6ea 5.8mm metal balls
6ea 5.8mm white nylon ball ends

pcd 01/10/94

The listed below product additionally sets really well with the product being reviewed.

Shock Rebuild Big Bore/Ultra

This is a shock restore kit for 2 Traxxas black plastic shocks. Suches as:

4 E-clips
2 C-clips
2 O-rings
8 Washers
2 Diaphrams

This product is regularly bought with the above discussed product.

Shock Shafts Chrome Xxl (2)

This is a set of XXL shock shafts for the Traxxas shocks.

Includes: 2 shock shafts

Features: solidified chrome/steel construction

Specs: 2 1/8" long or 54mm
1/16" diameter or 1.5mm

Requires: Bonus long shocks

Comments: These are threaded on one end, and have the slots for e-clips on the
other.

4/16/97
AST

This is a amazing addition to the product presently being reviewed.

Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set consists of the spring retainers that hold the springs in
place over the shock body and the piston heads that manage the quantity
of oil flow in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for 2 shocks.
Fits the shocks on most Traxxas nitro and electrical powered vehicles.
Two hole piston head for greater dampening or three hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    2 upper and 2 lower spring retainers
    2 2 hole piston head covers
    Two 3 hole piston head covers

NEEDS:
Disassembly of shock to set up parts.