Traxxas Shrt Rod Ends/Ball Cnnctr (6)

This are Rod Ends Short for the Nitro T-Maxx.
These rods ends connect to turnbuckles for front/rear.

FEATURES:
Black nylon rod ends
Steel pivot balls

SUCHES AS:
Six nylon rod ends
Six pivot balls

REQUIRES:
Turnbuckles: TRAC6338

SPECS:
Length: .695" (17.6mm)
Inner Size: .217" (5.5mm)

REMARKS:
Will work only for the Nitro T-Maxx.

This is a wonderful enhancement to the product presently being reviewed.

3 X 15Mm Button Hex Screw (6)

This is a package of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel building, Black in color
Used on the Traxxas Revo monster truck, can likewise be utilized in any
    application where a 3x15mm button head screw is required

SUCHES AS:
Six 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Size: 3mm

Many others have bought this product along with the product that you are presently reviewing.

Antenna Tube W/ Cap, Black

This is a basic replacement Antenna Tube with Cap from Dubro
This product can be utilized anywhere an antenna tube is needed to support
a receiver antenna wire.

FEATURES:
Black plastic building

SUCHES AS:
One antenna tube
One antenna tube cap
One receiver antenna wire sleeve

REQUIRES:
Nothing. This is a direct fit part for any boat, automobile, etc. that uses
    a basic size antenna tube.

SPECS:
Length: 12 1/4" (311mm)
Size: 1/8" (3.2mm)

You will certainly like this product if you have the product just above mentioned.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on vehicle

Here is a excellent product that several others have purchased the exact same time.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Construction

SUCHES AS:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Density: 2.0 mm (0.082")

REMARKS:
None

Want another excellent product to match the above pointed out product?

Rod Ends/Ball Connector (6)

These are 5.8mm ball ends and balls utilize in the LS II race truck kit.

Kit consists of: 6ea 5.8mm metal balls
6ea 5.8mm white nylon ball ends

pcd 01/10/94

The below product also pairs truly well with the product being reviewed.

Shock Rebuild Big Bore/Ultra

This is a shock restore set for 2 Traxxas black plastic shocks. Includes:

4 E-clips
2 C-clips
2 O-rings
8 Washers
2 Diaphrams

This product is often bought with the above pointed out product.

Shock Shafts Chrome Xxl (2)

This is a set of XXL shock shafts for the Traxxas shocks.

Includes: Two shock shafts

Features: hardened chrome/steel building

Specs: 2 1/8" long or 54mm
1/16" diameter or 1.5mm

Requires: Bonus long shocks

Comments: These are threaded on one end, and have the slots for e-clips on the
other.

4/16/97
AST

This is a wonderful enhancement to the product presently being reviewed.

Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set consists of the spring retainers that hold the springs in
restaurant over the shock body and the piston heads that control the quantity
of oil circulation in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for two shocks.
Fits the shocks on many Traxxas nitro and electric powered vehicles.
Two hole piston head for greater dampening or two hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    Two upper and two lower spring retainers
    Two 2 hole piston head covers
    Two 3 hole piston head covers

REQUIRES:
Disassembly of shock to install parts.