Traxxas Shrt Rod Ends/Ball Cnnctr (6)

This are Rod Ends Short for the Nitro T-Maxx.
These rods ends connect to turnbuckles for front/rear.

FEATURES:
Black nylon rod ends
Steel pivot balls

SUCHES AS:
6 nylon rod ends
6 pivot balls

REQUIRES:
Turnbuckles: TRAC6338

SPECS:
Length: .695" (17.6mm)
Inner Size: .217" (5.5mm)

COMMENTS:
Will work only for the Nitro T-Maxx.

This is a superb enhancement to the thing presently being discussed.

3 X 15Mm Button Hex Screw (6)

This is a bundle of six 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel construction, Black in color
Utilized on the Traxxas Revo beast truck, can likewise be used in any
    application where a 3x15mm button head screw is needed

SUCHES AS:
6 3x15mm Traxxas Button Head Screws

REQUIRES:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Size: 3mm

Numerous others have acquired this thing in addition to the thing that you are presently checking out.

Antenna Tube W/ Cap, Black

This is a standard replacement Antenna Tube with Cap from Dubro
This item can be used anywhere an antenna tube is needed to support
a receiver antenna wire.

FEATURES:
Black plastic construction

SUCHES AS:
One antenna tube
One antenna tube cap
One receiver antenna wire sleeve

REQUIRES:
Nothing. This is a direct fit part for any boat, car, etc. that utilizes
    a standard size antenna tube.

SPECS:
Length: 12 1/4" (311mm)
Size: 1/8" (3.2mm)

You will certainly enjoy this thing if you have the thing above stated.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

Right here is a terrific thing that numerous others have bought at the same time.

Tie Bar Fiberglass

This is a Firberglass Tie Bar by Traxxas for the SRT

FEATURES:
Fiberglass Building and construction

SUCHES AS:
One Tie Bar

REQUIRES:
Suspension Pins (TRAC4940)

SPECS:
Length: 98.4 mm (3.875")
Width: 7.9 mm (0.3125")
Thickness: 2.0 mm (0.082")

COMMENTS:
None

Want another terrific thing to enhance the above mentioned thing?

Rod Ends/Ball Connector (6)

These are 5.8mm ball ends and balls use in the LS II race truck kit.

Kit suches as: 6ea 5.8mm metal balls
6ea 5.8mm white nylon ball ends

pcd 01/10/94

The below thing likewise pairs actually well with the thing being discussed.

Shock Rebuild Big Bore/Ultra

This is a shock restore kit for 2 Traxxas black plastic shocks. Includes:

4 E-clips
2 C-clips
2 O-rings
8 Washers
2 Diaphrams

This thing is regularly acquired with the above mentioned thing.

Shock Shafts Chrome Xxl (2)

This is a set of XXL shock shafts for the Traxxas shocks.

Includes: 2 shock shafts

Features: solidified chrome/steel construction

Specs: 2 1/8" long or 54mm
1/16" size or 1.5mm

Requires: Bonus long shocks

Comments: These are threaded on one end, and have the slots for e-clips on the
other.

4/16/97
AST

This is a superb enhancement to the thing presently being discussed.

Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set includes the spring retainers that hold the springs in
location over the shock body and the piston heads that control the quantity
of oil circulation in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for 2 shocks.
Fits the shocks on a lot of Traxxas nitro and electrical powered vehicles.
Two hole piston moving towards higher dampening or three hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    2 upper and 2 lower spring retainers
    2 2 hole piston head covers
    Two 3 hole piston head covers

REQUIRES:
Disassembly of shock to install parts.