Traxxas Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

You will certainly enjoy this item if you have the item just above mentioned.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits a number of Traxxas
automobiles. .
Consists of: 1 gear just

Regularly acquired with the thing that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below thing also pairs really well with the thing being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Want an additional excellent thing to compliment the above mentioned thing?

30T Idler Gear Steel

This is the optional Steel Idler Equipment for lots of Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler gear

REQUIRES:
Setup on vehicle

Right here is an additional thing that praises the thing being gone over.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

REQUIRES:
Disassembly of slipper clutch

Right here is an additional thing that praises the thing being gone over.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Automobile

This thing is often acquired with the above mentioned thing.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic construction

CONSISTS OF:
One spur gear

SPECIFICATIONS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

Right here is a excellent thing that numerous others have actually bought at the exact same time.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide from the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

The listed below thing also pairs really well with the thing being gone over.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.