Traxxas Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

You will like this product if you have the product previously discussed.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive equipment that fits numerous Traxxas
automobiles. .
Consists of: 1 equipment just

Regularly acquired with the item that you are currently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The below item additionally sets truly well with the item being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Want an additional fantastic item to match the above pointed out item?

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Setup on vehicle

Below is an additional item that compliments the item being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

REQUIRES:
Disassembly of slipper clutch

Below is an additional item that compliments the item being discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Hub
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building
Silver in Color

CONSISTS OF:
One Slipper Press Plate
One Slipper Press Plate Hub

REQUIRES:
Assembly onto Vehicle

This item is often acquired with the above pointed out item.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic building

CONSISTS OF:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

Below is a fantastic item that many others have bought at the exact same time.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

The below item additionally sets truly well with the item being discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.