Traxxas Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

You will certainly love this thing if you have the thing above mentioned.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive gear that fits numerous Traxxas
vehicles. .
Consists of: 1 gear only

Regularly gotten with the thing that you are currently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below thing also sets truly well with the thing being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Want another great thing to compliment the above stated thing?

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler gear

NEEDS:
Setup on vehicle

Right here is another thing that compliments the thing being talked about.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

INCLUDES:
One Steel Disc
Three Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

Right here is another thing that compliments the thing being talked about.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Automobile

This thing is frequently gotten with the above stated thing.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for designs with a slipper clutch.
Black plastic building

INCLUDES:
One spur gear

SPECS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 90T gear (TRAC4690).

Right here is a great thing that numerous others have actually bought at the very same time.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide from the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

The listed below thing also sets truly well with the thing being talked about.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.