Traxxas Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

You will love this thing if you have the thing above discussed.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive equipment that fits numerous Traxxas
automobiles. .
Consists of: 1 equipment just

Frequently bought with the thing that you are currently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The below thing likewise pairs actually well with the thing being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Want another fantastic thing to enhance the above mentioned thing?

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler equipment

REQUIRES:
Installation on automobile

Right here is another thing that praises the thing being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Kit for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Steel Disc
3 Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Guidelines

REQUIRES:
Disassembly of slipper clutch

Right here is another thing that praises the thing being discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Arena Truck.

FEATURES:
Pot Metal Building
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

REQUIRES:
Assembly onto Vehicle

This thing is regularly bought with the above mentioned thing.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Developed for designs with a slipper clutch.
Black plastic construction

INCLUDES:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

REMARKS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

Right here is a fantastic thing that numerous others have purchased the same time.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

The below thing likewise pairs actually well with the thing being discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

REMARKS:
This part fit the standard and XL version of both the Stampede
and Rustler.