Traxxas Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

You will enjoy this product if you have the product previously pointed out.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits a number of Traxxas
cars. .
Includes: 1 equipment only

Frequently gotten with the product that you are currently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below product additionally sets really well with the product being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Want another great product to enhance the above pointed out product?

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler equipment

NEEDS:
Setup on car

Right here is another product that compliments the product being discussed.

Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Set for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One Steel Disc
3 Friction Pads
2 Springs
One 4mm Lock Nut
One 5mm Lock Nut
Instructions

NEEDS:
Disassembly of slipper clutch

Right here is another product that compliments the product being discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Building and construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Automobile

This product is frequently gotten with the above pointed out product.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Equipment for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic building and construction

INCLUDES:
One spur equipment

SPECIFICATIONS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is also a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

Right here is a great product that several others have bought at the exact same time.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide from the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

The listed below product additionally sets really well with the product being discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL variation of both the Stampede
and Rustler.