Traxxas Servo Connector, Y-Adapter For Dual-Servo Steering Revo

This is the Servo Y Harness for the Dual Steering Servos
for the REVO from Traxxas.

FEATURES:
Futaba J ports (one male to enter into the RX and 2 female to
go to the servos)

INCLUDES:
One Y harness w/two 3" zip ties

NEEDS:
Absolutely nothing

SPECIFICATIONS:
Length: 3" (76mm) approx

This item is frequently bought with the above mentioned item.

Castle Bec 10Amp (25 Volt Max Input)

This is the CC BEC 10A Receiver Battery Remover by Castle Creations.

FEATURES:
Eliminates the requirement for a receiver and servo battery pack
Draws higher voltage from the motor batteries and drops it to a
    voltage level ideal for the receiver and servos

INCLUDES:
One CC BEC receiver battery remover

NEEDS:
Setup in the aircraft

SPECIFICATIONS:
Length: 1.2" (30mm)
Width: .6" (15mm)
Height: .4" (10mm)
Weight: .4oz (11g)
Input voltage: 5V to 25.2V (2S to 6S LiPo)
Present output: 12 volts input = 7 amps* constant, 10 amp peak;
    24 volts input = 5 amps* constant, 7 amp peak
    *Ratings are identified with a 5mph air flow on the BEC
Selectable Output: 4.8 - 9.0V via the Castle Link (sold individually)
    Default voltage is 5.1V

The listed below item additionally pairs really well with the item being reviewed.



These are the EMS Unassembled Female Radio System Connectors.

FEATURES:
Compatible with Hitec, Airtronics Z and JR systems
Enables modelers to custom make their own extensions, servo leads,
    battery leads and more
Gold plated for high conductivity and dependability
Fits wire sizes from 20 to 30 AWG
No soldering required
Two year restricted guarantee

INCLUDES:
15 pins, 5 inner male ports and 5 female shells,
    and direction sheet

NEEDS:
Servo wire (HRCM3001)
Wire crimping tool

REMARKS:
For the Male Connectors, order EMOM0017

This item is frequently bought with the above mentioned item.

King Off-Rd Pggybck Shocks w/Faux Reservoir 100

This is a pair of King Off-Road 100mm Racing Shocks w/Faux Tank from RC4WD

FEATURES:
Machined billet aluminum building
Dual spring design
King logo on faux piggyback and retainer ring

INCLUDES:
Two 1/10 scale King Off-Road 110mm Racing Shocks w/Faux Tank

SPECIFICATIONS:
Hole to Hole (Compressed): 2.75" (70mm)
Hole to Hole (Uncompressed): 3.93" (100mm)
Overall Length: 4.28" (108.9mm)
Travel Length: 1.18" (30mm)
Shock Body OD: 0.39" (10mm)
Spring Body OD: 0.57" (14.5mm)
Shaft Diameter: 0.17" (3.5mm)
Weight: 0.9oz (26g)

REMARKS:
King Off-Road is a registered hallmark of the King Off-Road Shock
    business. The King Off-Road logo is property of King Off-Road
    Shocks.

This item is frequently bought with the above mentioned item.

Cc Blower Sct/Sv3 Fan

This is the Cooling Fan for the Castle Creations Sidewinder 3,
or Sidewinder SCT Electronic Speed Controls.

**Will not deal with older design cases used on the**
**non-waterproof Sidewinder SCT and initial Sidewinder 3.**

FFEATURES:
Snaps onto ESC, no screws required

INCLUDES:
Fan with Wire Lead and Adapter
Fan Shroud

SPECIFICATIONS:
Input Voltage: 4.8 - 7.4V
Optimum RPM: 14,000
Wire Length: 11.4" (290mm)
Water resistant: NO, get rid of prior to exposing ESC to moisture