Traxxas Sealed Receiver Box (Slash)

This is the Receiver Box for the 2WD Traxxas Slash Truck.

FEATURES:
Replaces damaged receiver boxes
Constructed of black plastic

CONSISTS OF:
One top and bottom half receiver box for the Traxxas Slash
Hardware

REQUIRES:
Setting up receiver and bolting receiver box to chassis.

Want an additional excellent thing to match the above discussed thing?

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Completely assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Attaches to the differential with one screw pin
Works on the front or rear, right or left of vehicle

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

REQUIRES:
Setting up on chassis

This thing is often bought with the above discussed thing.

Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

CONSISTS OF:
4 Blue Rubber Pivot Ball Boots
4 Black Dust Boot Retainer
4 Blue Notched Dust Boot Retainer
4 Blue Rubber Boot Plugs
4 nylon Pivot Ball Retainers
Instruction sheet

REQUIRES:
Two plans had to finish truck

This thing is often bought with the above discussed thing.



This is the Castle Creations Sidewinder SV3 12V Electronic Speed Control
    and the 1406 Series 4600kV Sensorless Brushless Motor.

FEATURES:
SV3 12V ESC (CSEM0115)
Advised for all 1/10 scale buggy and truggy applications that
    weigh less than 5lbs (2.25kg) all set to run (not for use in much heavier
    cars such as E-Revos or E-Maxx class cars)
USB programs ability through Castle Link USB adapter (not consisted of,
    order CSEM6300)
Water resistant for use in nearly every environment (not planned for
    operation while immersed in liquid)
Reversible with reverse lockout
    1406 Series 4600kV Motor (CSEC0000)
540 size can replaces lots of stock brushed motors
4 magnet, four pole rotor for greater torque
1.4" diameter slotted stator
Easily removable end bell

CONSISTS OF:
Sidewinder SV3 12V ESC with 13 gauge Battery Wires with Pre-Tinned
    Leads, 4mm Female Bullets for Motor Connection, Receiver Port,
    On/Off Switch, Directions, 4600kV 1406 series Brushless Motor
    with 4mm Male Bullet Connectors

REQUIRES:
Battery port of modeler's choice

SPECS:
ESC;
Input Voltage: 2S LiPo minimum, THREE LiPo optimum, 9 cell NiCd/NiMH
Brake: Proportional
Reversible: Yes, with lockout
Dimensions: 1.93 x 1.48 x 0.79" (49 x 38 x 20mm)
Weight: 1.96 oz (55.5 g) with 5" (127mm) long battery wires and no
    battery port
    Motor;
kV Rating: 4600
Can Length: 1.9" (49mm)
Can Diameter: 1.4" (36mm)
Shaft Diameter: 1/8" (3.2mm)
Weight: 5.9 oz (169.5 g)
Port: 4mm gold
Wire Length: 9.5" (241mm)