Traxxas Ring Gear, Differential/ Pinio

This is the Differential Ring and Pinion Gear for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Differential Ring Gear
One Differential Pinion Gear

REQUIRES:
Setup in differential assembly

SPECS:
Pinion Gear:
Tooth: 13T
Inner Size: 5mm (0.20")
Ring Gear:
Tooth: 37T
Inner Size: 6mm (0.24")

This item compliments the above discussed item.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This item compliments the main item below.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this product if you have the product previously discussed.

6 X 12 X 4Mm Ball Bearing (2) Blue Rubber Sheild R Evo

This is a 6X12mm Ball Bearing Set from Traxxas.

FEATURES:
Steel construction
Blue rubber dirt shields

INCLUDES:
(2) ball bearings, Part #5117

SPECS:
Inside diameter: 6mm
Outside diameter: 12mm
Width: 4mm

REMARKS:
This bearing set is used in the transmission and differentials of
    the Revo.

Right here is one more item that compliments the item being discussed.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to vehicle

SPECS:
Inner Size: 10mm
External Size: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are used to support the Main Clutch (one needed).

This is a superb enhancement to the item currently being discussed.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Hub for use on the Traxxas Slash 4x4.

FEATURES:
Solidified steel construction

INCLUDES:
One Drive Hub
One Screw Pin

REQUIRES:
Setup on the vehicle

SPECS:
Length: 19mm (0.75")
Size: 12mm (0.47")

Right here is a fantastic item that lots of others have actually purchased the same time.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Put together w/Rod Ends

INCLUDES:
Two rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the vehicle

Get this item to enhance the one you are reading about.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Put together w/Rod Ends

INCLUDES:
Two front 39mm (69mm center to center) turnbuckles and guideline
    sheet

REQUIRES:
Setup on the vehicle

This item is frequently acquired with the above stated item.

Slipper Clutch Complete Stampede 4X4

This is the Complete Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Complete slipper clutch assembly
Pre-assembled

INCLUDES:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Setup in vehicle