Traxxas Ring Gear, Differential/ Pinio

This is the Differential Ring and Pinion Gear for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction

INCLUDES:
One Differential Ring Gear
One Differential Pinion Gear

REQUIRES:
Setup in differential assembly

SPECIFICATIONS:
Pinion Gear:
Tooth: 13T
Inner Diameter: 5mm (0.20")
Ring Gear:
Tooth: 37T
Inner Diameter: 6mm (0.24")

This thing praises the above gone over thing.

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This thing praises the main item right here.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this thing if you have the thing above discussed.

6 X 12 X 4Mm Ball Bearing (2) Blue Rubber Sheild R Evo

This is a 6X12mm Ball Bearing Set from Traxxas.

FEATURES:
Steel construction
Blue rubber dirt guards

INCLUDES:
(2) ball bearings, Part #5117

SPECIFICATIONS:
Inside size: 6mm
Outdoors size: 12mm
Width: 4mm

REMARKS:
This bearing set is used in the transmission and differentials of
    the Revo.

Right here is an additional thing that praises the thing being gone over.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

INCLUDES:
2 Ball Bearings

REQUIRES:
Assembly to car

SPECIFICATIONS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

REMARKS:
These bearings are used to support the Primary Clutch (one required).

This is a great addition to the thing presently being gone over.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Hub for use on the Traxxas Slash 4x4.

FEATURES:
Solidified steel construction

INCLUDES:
One Drive Hub
One Screw Pin

REQUIRES:
Setup on the car

SPECIFICATIONS:
Length: 19mm (0.75")
Diameter: 12mm (0.47")

Right here is a terrific thing that many others have actually purchased the same time.

49Mm Turnbuckles Camber Link Rr

These are the Traxxas 49mm Turnbuckle Camber Links
for the Outlaw, Rustler VXL and Stampede VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 rear 49mm (82mm center to center) turnbuckles

REQUIRES:
Setup on the car

Get this thing to enhance the one you are reading about.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 front 39mm (69mm center to center) turnbuckles and guideline
    sheet

REQUIRES:
Setup on the car

This thing is frequently acquired with the above stated thing.

Slipper Clutch Complete Stampede 4X4

This is the Total Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Total slipper clutch assembly
Pre-assembled

INCLUDES:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Setup in car