Traxxas Rebuild Kit, Slipper Clutch (S

This is the Slipper Clutch Rebuild Package for the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel building

INCLUDES:
One Steel Disc
Three Friction Pads
Two Springs
One 4mm Lock Nut
One 5mm Lock Nut
Directions

NEEDS:
Disassembly of slipper clutch

Want another fantastic item to enhance the above pointed out item?

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Vehicle

Below is another item that compliments the item being discussed.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is another item that compliments the item being discussed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

This item is frequently acquired with the above pointed out item.

Spur Gear (86T) 48P

This is a Traxxas 48P, 86T Spur Gear for designs with
Torque Control Slipper Clutch.

FEATURES:
48 pitch
86 tooth
Created for designs with a slipper clutch.
Black plastic building

INCLUDES:
One spur equipment

SPECS:
Pitch: 48
Tooth: 86

COMMENTS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 90T equipment (TRAC4690).

Below is a fantastic item that many others have purchased the exact same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Setup on to slipper shaft
Remaining clutch pieces

The listed below item likewise sets actually well with the item being discussed.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon building
Black in color
.8 Module pitch

INCLUDES:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Below is a fantastic item that many others have purchased the exact same time.

3 X 6Mm Cap Hex Screws (6)

These are 3x5mm Backplate screws for the Traxxas 2.5 Engine.

FEATURES:
Black steel construction.

INCLUDES:
Six black steel cap head screws.

REQUIRES:
Assembly on coverplate.

SPECS:
Length: 5mm
Diameter: 3mm

COMMENTS:
These may likewise be referred to as coverplate screws.

Several others have acquired this item along with the item that you are presently reading about.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Created for designs with a slipper clutch
Black plastic building

INCLUDES:
One spur equipment

SPECS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is likewise a 76T equipment (TRAC4676),
    83T equipment (TRAC4683) and 86T equipment (TRAC4686).