Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the car

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037

Lots of others have actually acquired this item together with the item that you are currently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item is frequently acquired with the above discussed item.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Setup on car

Want an additional great item to compliment the above discussed item?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits numerous Traxxas
cars. .
Consists of: 1 gear just

This is a great addition to the item currently being talked about.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

The listed below item additionally pairs truly well with the item being talked about.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.

The listed below item additionally pairs truly well with the item being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Lots of others have actually acquired this item together with the item that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Lots of others have actually acquired this item together with the item that you are currently checking out.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Lightweight carbon fiber composite transmission case
Longer motor installing slots for more gear ratio mixes
CNC 6061 aluminum motor plate, heat sink and arm install
Bigger open area for a bigger motor heat sink
Thirty day restricted warranty starting at date of purchase-valid
    in the United States just

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Lots of others have actually acquired this item together with the item that you are currently checking out.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
steering knuckles connect to.

FEATURES:
Nylon building and construction, black in color
Stamped right and left to insure correct installation

CONSISTS OF:
2 RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and steering knuckles