Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the automobile

COMMENTS:
For primary differential w/ steel ring - TRAC6380
Planet gear shafts - TRAC6382
Silicon grease _- TRAC6037

Lots of others have actually acquired this thing together with the thing that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This thing is often acquired with the above stated thing.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for many Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Setup on automobile

Want one more fantastic thing to match the above stated thing?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits several Traxxas
automobiles. .
Includes: 1 gear only

This is a wonderful addition to the thing presently being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

The listed below thing additionally sets truly well with the thing being reviewed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

The listed below thing additionally sets truly well with the thing being reviewed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Lots of others have actually acquired this thing together with the thing that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Lots of others have actually acquired this thing together with the thing that you are presently checking out.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Equipment Case with Aluminum Motor Plate
for the Traxxas 1/10 Outlaw, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Lightweight carbon fiber composite transmission case
Longer motor mounting slots for more gear ratio mixes
CNC 6061 aluminum motor plate, heat sink and arm install
Larger open area for a bigger motor heat sink
Thirty day limited guarantee beginning at date of purchase-valid
    in the United States only

INCLUDES:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Lots of others have actually acquired this thing together with the thing that you are presently checking out.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These blocks install to the front A-arms and is exactly what the
steering knuckles attach to.

FEATURES:
Nylon building and construction, black in color
Stamped right and delegated insure appropriate installation

INCLUDES:
Two RPM 30° Front Caster Blocks

NEEDS:
Assembly in between A-arms and steering knuckles