Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic main differential

SUCHES AS:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Setup on the car

COMMENTS:
For main differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037

Many others have purchased this thing in addition to the thing that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

SUCHES AS:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This thing is frequently purchased with the above stated thing.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel building

SUCHES AS:
One steel 30T idler equipment

REQUIRES:
Setup on car

Want an additional fantastic thing to enhance the above stated thing?

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits numerous Traxxas
vehicles. .
Includes: 1 equipment just

This is a wonderful addition to the thing presently being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

SUCHES AS:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on car

The below thing likewise pairs really well with the thing being gone over.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building
Steel idler shaft

SUCHES AS:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

The below thing likewise pairs really well with the thing being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Many others have purchased this thing in addition to the thing that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

SUCHES AS:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Many others have purchased this thing in addition to the thing that you are presently checking out.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Lightweight carbon fiber composite transmission case
Longer motor mounting slots for more equipment ratio mixes
CNC 6061 aluminum motor plate, heat sink and arm mount
Bigger open area for a larger motor heat sink
Thirty day minimal guarantee starting at date of purchase-valid
    in the United States just

SUCHES AS:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Many others have purchased this thing in addition to the thing that you are presently checking out.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs mount to the front A-arms and is what the
steering knuckles connect to.

FEATURES:
Nylon building, black in color
Stamped right and delegated insure correct installation

SUCHES AS:
Two RPM 30° Front Caster Blocks

REQUIRES:
Assembly in between A-arms and steering knuckles