Traxxas Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Setup on the car

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World equipment shafts - TRAC6382
Silicon grease _- TRAC6037

Numerous others have acquired this item along with the item that you are presently checking out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This item is regularly acquired with the above discussed item.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Setup on car

Want another terrific item to enhance the above discussed item?

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive equipment that fits numerous Traxxas
automobiles. .
Includes: 1 equipment only

This is a amazing addition to the item presently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on car

The below item also pairs truly well with the item being discussed.

Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic construction
Steel idler shaft

CONSISTS OF:
One gearbox
One idler shaft

COMMENTS:
This part fit the standard and XL version of both the Stampede
and Rustler.

The below item also pairs truly well with the item being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Thickness: 0.5mm

Numerous others have acquired this item along with the item that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Numerous others have acquired this item along with the item that you are presently checking out.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Outlaw, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Light weight carbon fiber composite transmission case
Longer motor installing slots for more equipment ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm install
Bigger open location for a bigger motor heat sink
Thirty day restricted guarantee beginning at date of purchase-valid
    in the United States only

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Numerous others have acquired this item along with the item that you are presently checking out.

Caster Blocks, For Traxxas Electric Slash, Stampede, Rustler, Ni

These are RPM 30° Front Caster Blocks for the Traxxas
Electric Stampede and Rustler.
These obstructs install to the front A-arms and is what the
guiding knuckles attach to.

FEATURES:
Nylon construction, black in color
Stamped right and left to insure appropriate setup

CONSISTS OF:
2 RPM 30° Front Caster Blocks

REQUIRES:
Assembly between A-arms and guiding knuckles