Traxxas Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FUNCTIONS:
All these gears and shafts are made of metal(probably with a low
quantity of steel).

CONSISTS OF:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear positioning shaft

WAJ
1/16/94

Get this product to boost the one you read about.

Sealed Aluminum Differential Case For Traxxas 2Wd Electric

This is the optional Hot-Racing Aluminum Differential Case
for the Traxxas Bandit, Rustler, 2WD Stampede, 2WD Slash
and Beast Jam Cars

FUNCTIONS:
CNC aluminum construction diff case, black in color
Hardened steel gear
Sealed differentials permits tuning to track conditions by altering
    weight of diff oil
Four O-rings help seal against fluid leak
Thirty day minimal warranty beginning at date of purchase- legitimate
    in the United States only

CONSISTS OF:
Sealed Differential Case
Four O-Rings
Two Screws

SPECS:
Outdoors Diameter: 1.48" (37.5mm)
Shaft Diameter: .200" (5.10mm)
Total Density: 0834" (21.2mm)

Lots of others have actually acquired this product in addition to the product that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Below is another product that compliments the product being gone over.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly like this product if you have the product previously discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

This product is often acquired with the above mentioned product.

Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Lightweight carbon fiber composite transmission case
Longer motor mounting slots for more gear ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm mount
Larger open location for a larger motor heat sink
Thirty day minimal warranty beginning at date of purchase-valid
    in the United States only

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Frequently acquired with the product that you are presently checking out.

Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Bandit, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Directions

Needs: Setup on the car

Lots of others have actually acquired this product in addition to the product that you are presently checking out.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits numerous Traxxas
vehicles. .
Consists of: 1 gear only