Traxxas Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

CONSISTS OF:
4 Blue Rubber Pivot Ball Boots
4 Black Dust Boot Retainer
4 Blue Notched Dust Boot Retainer
4 Blue Rubber Boot Plugs
4 nylon Pivot Ball Retainers
Instruction sheet

NEEDS:
Two plans had to finish truck

This item compliments the above talked about item.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
use on the Traxxas Revo series.

FEATURES:
Nylon Construction
Black in Color
Allows for Oversized Bearing use

CONSISTS OF:
One Left Axle Carrier
One Right Axle Carrier
4 Dust Boot Retainers
Two Bearing Spacers

NEEDS:
Installation

Want an additional great item to enhance the above stated item?

Driveshaft Boots (2) Revo

These are the replacement Drive Shaft Boots for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Rubber Construction
Blue in Color

CONSISTS OF:
Two Blue Rubber Driveshaft Boots

NEEDS:
Assembly onto Automobile

This item compliments the main item below.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Center Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless Steel Construction
Blue Rubber Sealed

CONSISTS OF:
Two 12mm x 18mm Blue Sealed Stainless Wheel Center Bearings

NEEDS:
Assembly onto Automobile

SPECIFICATIONS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Density: 4mm (0.15")

REMARKS:
These are for the Within the Wheel Centers, the Truck Needs
4 Overall of these Bearings.

Want an additional great item to enhance the above stated item?

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for use on the E-Revo

FUNCTIONS:
Stainless Steel bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside diameter: 6mm (0.24")
Outdoors diameter: 13mm (0.51")
Width: 5mm (0.20")

Often acquired with the item that you are currently reading about.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FUNCTIONS:
Fully put together
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Connects to the differential with one screw pin
Functions on the front or back, right or left of automobile

CONSISTS OF:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Instruction sheet

NEEDS:
Installing on chassis

This is a amazing addition to the item currently being talked about.

Pivot Balls W/Cap

These are the Pivot Balls and Pivot Ball Cap Bushings for the
Traxxas T-Maxx and E-Maxx 4WD Radio Control Monster Trucks.
Two of these pivot balls fit into the axle providers at each wheel
    The pivot ball cap bushings fit in between the pivot balls
and the aluminum caps.

FEATURES:
Changes stock pivot balls and pivot ball cap bushings.
Pivot balls are made from steel, pivot ball cap bushings are made from
    plastic.

INCLUDES:
4 pivot balls.
Four pivot ball cap bushings

NEEDS:
Threading the pivot balls through the axle providers and into the
    suspension arms. Placing pivot ball cap bushings in between the pivot
    balls and aluminum caps.