Traxxas Pivot Ball Caps & Dust Boots

This is the replacement Pivot Ball and Dust Cap Boot Set
    for the Traxxas Revo, E-Revo and T-Maxx 3.3 vehicles.

FEATURES:
Nylon and Rubber Construction
Blue and Black in Color

INCLUDES:
Four Blue Rubber Pivot Ball Boots
Four Black Dust Boot Retainer
Four Blue Notched Dust Boot Retainer
Four Blue Rubber Boot Plugs
Four nylon Pivot Ball Retainers
Direction sheet

REQUIRES:
Two bundles had to finish truck

This product compliments the above talked about product.

Axle Carriers Use Larger 6 X 1

These are the Optional Axle Carriers L & R for
usage on the Traxxas Revo series.

FEATURES:
Nylon Construction
Black in Color
Enables Oversized Bearing use

INCLUDES:
One Left Axle Carrier
One Right Axle Carrier
Four Dust Boot Retainers
Two Bearing Spacers

REQUIRES:
Setup

Want another excellent product to match the above stated product?

Driveshaft Boots (2) Revo

These are the replacement Drive Shaft Boots for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Rubber Construction
Blue in Color

INCLUDES:
Two Blue Rubber Driveshaft Boots

REQUIRES:
Assembly onto Car

This product compliments the main item right here.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless-steel Construction
Blue Rubber Sealed

INCLUDES:
Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

REQUIRES:
Assembly onto Car

SPECIFICATIONS:
Outer Diameter: 18mm (0.70")
Inner Diameter: 12mm (0.47")
Thickness: 4mm (0.15")

COMMENTS:
These are for the Inside of the Wheel Hubs, the Truck Requires
Four Total of these Bearings.

Want another excellent product to match the above stated product?

Bbs Blue Rubber Sealed 6 X 13M

This is a set of Traxxas 6x13x5mm Ball Bearings
for usage on the E-Revo

FEATURES:
Stainless-steel bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 6x13x5mm ball bearings Part #5180

SPECIFICATIONS:
Inside size: 6mm (0.24")
Outside size: 13mm (0.51")
Width: 5mm (0.20")

Frequently acquired with the product that you are presently reading about.

Driveshaft Assembly (1)

This is the Driveshaft Assembly for the Traxxas Revo 3.3.
and the T-Maxx 3.3.

FEATURES:
Fully assembled
Plastic telescoping driveshaft with steel universals
Blue rubber boot guards telescoping areas from dirt
Attaches to the differential with one screw pin
Functions on the front or back, right or left of vehicle

INCLUDES:
#5458X Yoke, TRAC9798
#5145 Screw Pin, TRAC5145
#5450 Halfshaft, TRAC7450
#5452 U Joint, TRAC7452
#5459 Rubber Boot, TRAC7459
Direction sheet

REQUIRES:
Installing on chassis

This is a wonderful addition to the product presently being talked about.

Pivot Balls W/Cap

These are the Pivot Balls and Pivot Ball Cap Bushings for the
Traxxas T-Maxx and E-Maxx 4WD Radio Control Monster Trucks.
Two of these pivot balls suit the axle providers at each wheel
    The pivot ball cap bushings fit in between the pivot balls
and the aluminum caps.

FEATURES:
Replaces stock pivot balls and pivot ball cap bushings.
Pivot balls are made from steel, pivot ball cap bushings are made from
    plastic.

INCLUDES:
Four pivot balls.
Four pivot ball cap bushings

REQUIRES:
Threading the pivot balls through the axle providers and into the
    suspension arms. Putting pivot ball cap bushings in between the pivot
    balls and aluminum caps.