Traxxas Nerf Bars, Chassis (Slash)

These are the replacement Nerf Bars for the 2WD Traxxas Slash.

FEATURES:
Black plastic building and construction

CONSISTS OF:
2 Nerf Bars for the Traxxas Slash

NEEDS:
Installation onto Car

Below is an additional thing that compliments the thing being reviewed.

Sealed Receiver Box (Slash)

This is the Receiver Box for the 2WD Traxxas Slash Truck.

FEATURES:
Changes damaged receiver boxes
Constructed of black plastic

CONSISTS OF:
One top and bottom half receiver box for the Traxxas Slash
Hardware

NEEDS:
Setting up receiver and bolting receiver box to chassis.

This is a fantastic enhancement to the thing presently being reviewed.

Hold Down, Battery Slash

This is the Hold Down Battery Set for the 2WD Traxxas Slash.

FEATURES:
Black nylon building and construction

CONSISTS OF:
One Battery Hold Down
One Retainer Hold Down
One Battery Post
One Foam Spacer
One Angled Body Clip

NEEDS:
Installation on the chassis

The below thing also pairs truly well with the thing being reviewed.

Bumper, Front/ Bumper Mount, F

This is the Front Bumper and Mount for the Traxxas Slash 4x4.

FUNCTIONS:
Solidified plastic building and construction
Black in color

CONSISTS OF:
One Front bumper
One Front bumper install

NEEDS:
Installation on chassis

Frequently bought with the thing that you are presently reviewing.

Susp Screw Pin Set #2640 (Hex Drive)

These are the Suspension Screws Pins for the
Traxxas Rustler, Stampede and Bandit.
The hinge pins hold the suspension arms to the bulkheads

FUNCTIONS:
Resilient steel building and construction

CONSISTS OF:
2 48mm pins
2 34mm pins
2 30mm pins
2 28mm pins
2 25mm pins

NEEDS:
Installation on the Rustler, Stampede or Bandit

REMARKS:
For a complete suspension pin set order TRAC4940

Get this thing to enhance the one you are reading about.

Suspension Arms Rear Slash 2Wd Rustler Stampede F/R Slash 4X4

This is the Left and Right Suspension Arms for the Traxxas Slash 4x4.

FUNCTIONS:
Solidified plastic building and construction
Front or rear application

CONSISTS OF:
One left suspension arm
One right suspension arm

NEEDS:
Installation on suspension assembly

SPECIFICATIONS:
Length: 100mm (3.94")
Width: 45mm (1.77")
Density: 11.5mm (0.45")

Below is a wonderful thing that lots of others have actually purchased the exact same time.

Front Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the optional RPM Front Shock Tower for the
Traxxas E-Stampede, E- Rustler, Bandit & Nitro Stampede.

FEATURES:
Plastic building and construction
Black in color

CONSISTS OF:
One Front Shock Tower for the Traxxas E-Stampede, E-Rustler, Bandit
    and Nitro Stampede

NEEDS:
Installation on the automobile

SPECIFICATIONS:
Width: 3.26" (83mm)
Height: 2.91" (74mm)
Density: .27" (7mm)

This is a fantastic enhancement to the thing presently being reviewed.

Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FUNCTIONS:
Composite nylon building and construction
Changes a used or damaged bellcrank set
May likewise be installed on the Traxxas Rustler, Bandit and 2WD Slash
    designs (assembled in various configurations depending upon design)

CONSISTS OF:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
2 Servo Arms
2 Shoulder Screws
2 3x15 Counter Sunk Device Screws
2 Hollow Balls
Four Bushings
Guideline Sheet

NEEDS:
Assembly and installation following the design manual and included
guideline sheet