Traxxas Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Bandit, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Instructions

Requires: Installation on the vehicle

This is a fantastic enhancement to the thing presently being discussed.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on vehicle

This thing is often gotten with the above stated thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing compliments the main item below.

Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FEATURES:
All these gears and shafts are made of metal(most likely with a low
amount of steel).

INCLUDES:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear positioning shaft

WAJ
1/16/94

Many others have gotten this thing together with the thing that you are presently checking out.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive gear that fits a number of Traxxas
vehicles. .
Consists of: 1 gear only

Many others have gotten this thing together with the thing that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

Want one more great thing to match the above stated thing?

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

Below is a great thing that lots of others have purchased the exact same time.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel construction
Natural color

INCLUDES:
Two front axles

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, usage
    TRAC2536.

Want one more great thing to match the above stated thing?

Turnbuckles Toe Link 61Mm (96Mm Ctr To Ctr) (2) (A Ssemb

These are the Traxxas 61mm Turnbuckle Toe Hyperlinks
for the Traxxas Stampede.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
Two 61mm (96mm center to center) turnbuckles

NEEDS:
Installation on the vehicle

This thing compliments the main item below.

Rear Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the RPM Rear Shock Tower for the
Traxxas E-Stampede, E-Rustler and E-Bandit.

FEATURES:
Strong nylon enhanced plastic construction
Uses all stock hardware (for installing shocks and so on)

INCLUDES:
One back shock tower

SPECS:
Width: 4.33" (110mm)
Height: 2.75" (70mm)
Density: 7mm