Traxxas Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Outlaw, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Instructions

Needs: Installation on the car

This is a superb addition to the product currently being reviewed.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

REQUIRES:
Installation on car

This product is regularly acquired with the above discussed product.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This product praises the main item below.

Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FUNCTIONS:
All these gears and shafts are made of metal(probably with a low
amount of steel).

INCLUDES:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear positioning shaft

WAJ
1/16/94

Numerous others have acquired this product along with the product that you are currently checking out.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits a number of Traxxas
vehicles. .
Consists of: 1 gear only

Numerous others have acquired this product along with the product that you are currently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Want an additional terrific product to compliment the above discussed product?

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

REQUIRES:
Installation on car

Below is a terrific product that lots of others have purchased the exact same time.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

INCLUDES:
2 front axles

REQUIRES:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, usage
    TRAC2536.

Want an additional terrific product to compliment the above discussed product?

Turnbuckles Toe Link 61Mm (96Mm Ctr To Ctr) (2) (A Ssemb

These are the Traxxas 61mm Turnbuckle Toe Hyperlinks
for the Traxxas Stampede.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 61mm (96mm center to center) turnbuckles

REQUIRES:
Installation on the car

This product praises the main item below.

Rear Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the RPM Rear Shock Tower for the
Traxxas E-Stampede, E-Rustler and E-Bandit.

FUNCTIONS:
Tough nylon enhanced plastic building and construction
Utilizes all stock hardware (for installing shocks etc.)

INCLUDES:
One back shock tower

SPECS:
Width: 4.33" (110mm)
Height: 2.75" (70mm)
Density: 7mm