Traxxas Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Bandit, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Directions

Requires: Installation on the vehicle

This is a great enhancement to the item presently being talked about.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel building

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on vehicle

This item is frequently purchased with the above pointed out item.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item compliments the main item here.

Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FEATURES:
All these gears and shafts are made of metal(most likely with a low
amount of steel).

INCLUDES:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear positioning shaft

WAJ
1/16/94

Many others have actually purchased this item along with the item that you are presently reading about.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive gear that fits a number of Traxxas
automobiles. .
Includes: 1 gear just

Many others have actually purchased this item along with the item that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Want an additional terrific item to compliment the above pointed out item?

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on vehicle

Right here is a terrific item that lots of others have actually purchased the exact same time.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
2 front axles

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

Want an additional terrific item to compliment the above pointed out item?

Turnbuckles Toe Link 61Mm (96Mm Ctr To Ctr) (2) (A Ssemb

These are the Traxxas 61mm Turnbuckle Toe Links
for the Traxxas Stampede.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Assembled w/Rod Ends

INCLUDES:
2 61mm (96mm center to center) turnbuckles

NEEDS:
Installation on the vehicle

This item compliments the main item here.

Rear Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the RPM Back Shock Tower for the
Traxxas E-Stampede, E-Rustler and E-Bandit.

FEATURES:
Tough nylon enhanced plastic building
Uses all stock hardware (for mounting shocks and so on)

INCLUDES:
One back shock tower

SPECIFICATIONS:
Width: 4.33" (110mm)
Height: 2.75" (70mm)
Thickness: 7mm