Traxxas Main Diff W/ Steel Ring Gear/ Side Cover Plate/ Sc Rews (Ban

This is the Main Diff with Steel Ring Gear from Traxxas
for the Bandit, Stampede and Rustler VXL series.

Includes: Main diff with steel ring gear
Side cover plate
Screws
Instructions

Requires: Setup on the car

This is a wonderful addition to the thing presently being reviewed.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Setup on car

This thing is frequently acquired with the above mentioned thing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outdoors size: 7/16" (11mm)
Width: 5/32" (4mm)

This thing praises the main item below.

Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FUNCTIONS:
All these gears and shafts are made from metal(probably with a low
amount of steel).

CONSISTS OF:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear alignment shaft

WAJ
1/16/94

Numerous others have actually acquired this thing in addition to the thing that you are presently reading about.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel top drive gear that fits several Traxxas
vehicles. .
Includes: 1 gear only

Numerous others have actually acquired this thing in addition to the thing that you are presently reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

Want one more great thing to enhance the above mentioned thing?

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

Below is a great thing that several others have actually purchased the exact same time.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building and construction
Natural color

CONSISTS OF:
Two front axles

NEEDS:
Absolutely nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

COMMENTS:
These will not work for the nitro versions. For that axle, use
    TRAC2536.

Want one more great thing to enhance the above mentioned thing?

Turnbuckles Toe Link 61Mm (96Mm Ctr To Ctr) (2) (A Ssemb

These are the Traxxas 61mm Turnbuckle Toe Hyperlinks
for the Traxxas Stampede.

FEATURES:
Metal and Nylon Building
Silver and Black in Color
Assembled w/Rod Ends

CONSISTS OF:
Two 61mm (96mm center to center) turnbuckles

NEEDS:
Setup on the car

This thing praises the main item below.

Rear Shock Tower, For Traxxas Slash/Rustler/Stampede/Bandit

This is the RPM Back Shock Tower for the
Traxxas E-Stampede, E-Rustler and E-Bandit.

FUNCTIONS:
Durable nylon enhanced plastic building and construction
Uses all stock hardware (for mounting shocks and so on)

CONSISTS OF:
One rear shock tower

SPECS:
Width: 4.33" (110mm)
Height: 2.75" (70mm)
Thickness: 7mm