Traxxas 8400Mah 11.1V 3-Cell 25C Lipo

This is the Traxxas Power Cell 11.1V 8400mAh 25C THREE LiPo Battery.

FEATURES:
Semi stiff building and construction does not require a hard case and removes
    wire harness connectors that can loosen and fail
Engineered particularly to fit Traxxas models
12AWG multi hair wire is soldered straight to the LiPo cells
    eliminating increased resistance from bullet connectors and
    accidental reversed polarity connections

CONSISTS OF:
Traxxas Power Cell 11.1V 8400mAh 25C LiPo THREE Battery with High
    Existing Adapter and JST/XH Balance Plug

NEEDS:
Balancer and LiPo suitable battery charger or LiPo battery charger with built-in
    balancer such as the Onyx 235, DTXP4235
LiPo charging bag

SPECIFICATIONS:
Configuration: 3S2P
Constant Discharge: 25C (210A)
Max Burst Rate: 50C (420A)
Watt Hours: 93.24
Charge Rate: 1C (8.4A)
Max Charge Rate: 2C (16.8A)
Measurements: 6.1 x 1.7 x 1.8" (155 x 44 x 45mm)
Weight: 21.7oz (615g)

REMARKS:
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.20V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER allow to Discharge listed below 2.5V per cell
NEVER take apart or customize pack electrical wiring in any method or leak cells
NEVER place on combustible products or leave unattended throughout
    charging
ALWAYS Charge in a fire-resistant location
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

The below item also sets really well with the item being talked about.

Adapter Traxxas ID LiPo Battery

This is the Traxxas iD LiPo Battery Adapter.

FEATURES:
Connects Traxxas iD LiPo batteries to LiPo chargers with separate
    balance ports

CONSISTS OF:
iD LiPo Battery Adapter with THREE Balance Port
Adapter with 2S Balance Port

SPECIFICATIONS:
Length: 5.2" (132mm) consisting of connectors

This item compliments the above talked about item.



This is the 2.4GHz Radio Controlled, Brushless Electric Powered,
Ready to Run Traxxas X-Maxx.

Ingenious New Characteristic Include;

**Exclusive Self-Righting Action, if automobile rolls upside down**
**just push a button on the transmitter and in most cases**
**the X-Maxx will flip upright onto its wheels.**

**One handed body mount and elimination system**
**removes body posts and pins.**

**Battery Retention System removes body clips or hook and loop straps**

**Shock towers also work as bring deals with and level supports**
    **when automobile is put upside down for maintenance.**

**Additional Technical Information Will Be Added When It Appears.**

FUNCTIONS:
Traxxas Stability Management (TSM): Superior tuning algorithms work on
    high-speed electronic elements to control wheel spin and steering
    instructions on loose dirt, concrete as well as ice and snow. TSM can be
    great tuned or shut off by adjusting the multi-function knob on
    the TQi transmitter or the slider in the Traxxas Link app
Chassis: Composite nylon tub, modular design offers easy access
    to critical elements, lower front and rear skids and integrated
    nerf bars for front, rear and side effect defense
Drive 4 wheel shaft drive, high-strength steel CV driveshafts with
    splined wheel hexes that get rid of axle pins, aluminum splined
    center driveshaft
Brushless Motor: Velineon 1600, 4 pole 1600Kv, 5mm shaft, aluminum
    heat sink
Motor Mount: Cradle design removes flexing, keyed pins lock equipment
    mesh in location
Radio: 2.4GHz TQi transmitter with 5-ch micro TSM telemetry ready
    receiver, BEC voltage and motor temperature level sensors set up,
    self righting button, integrated fail safe,
    can be geared up with the TQi Docking Base along with the iPhone,
    iPad or iPod touch* to develop a visual user interface for the
    automobile Traxxas Link TQi Wireless Module needed (not suched as)
Steering Servo: High-torque with aluminum heat sink, double shear
    bearing supported servo horn
Electronic Speed Control: Velineon VXL-6s 6S LiPo suitable
Transmission; Single speed
Differentials: Sealed solidified steel bevel, oil filled, minimal slip
Slipper Clutch: Double fan cooled
Battery Retention System: Integrated into chassis top brace for
    greater rigidness, removes body clips or hook and loop straps,
    adjustable for various batteries
Body: ProGraphix painted and trimmed
Body Mount System: Quick one-hand body installation and elimination,
    rotating rear lock mechanism removes body posts and clips
Suspension: Captured high-strength steel pins, double sheer
    connections, adjustable roll center
Shocks: GTX aluminum bodied, oil-filled, integrated wiper seal keeps
    shafts clean reducing seal wear
Shock Towers: Composite plastic building and construction, also work as bring
    deals with and level supports when automobile is put upside down
Tires: Aggressive all-terrain tread 8 x 4 x 4"
    foam inserts
Wheels: 4.3x5.7 inches (110x145mm), 17mm hexes
Steering: Bellcrank
Bumpers: Front and rear composite plastic with effect cushions
    behind each bumper to soften blows and add to durability
Ball Bearings: Sealed, full contact
Radio Box: Water resistant

CONSISTS OF:
RTR X-Maxx Truck with Brushless Motor, Radio, ESC, Painted Body,
    Quick Start Guide and Maintenance Tools

NEEDS:
Batteries: 2 THREE LiPo 5000mAh or greater
Battery Battery charger: Suitable with selected LiPo batteries
AA Cells: For for transmitter
LiPo Charging Bag

SPECIFICATIONS:
Vehicle;
Length: 29.84" (758mm)
Front Track: 22.26" (540mm)
Rear Track: 20.66" (525mm) distance from external edges of wheels
    measured side-to-side
Ground Clearance: 4" (102mm)
Weight: 19.1lbs (8.66kg)
Trip Height: 13.79" (350mm)
Overall Drive Ratio: 8.24
Wheelbase: 18.92" (480mm)
Shock Length: 7.4" (187mm)
Battery Tray Dimensions: 7.7 x 2 x 1.7" (197mm x 51.5mm x 44mm)
    Body;
Length:
Width:
Height:

REMARKS:
Available in the following colors;
    Blue, TRAD75BB
    Red, TRAD75RR

For Replacement Ball Bearings use:
    Qty. Size Place Qty. Bearing Set