Traxxas Input Shaft (Slipper Shaft)/ B

This is the Input Shaft for use on the Traxxas Slash 4x4 Vehicles.

FEATURES:
Steel construction
Black in color

CONSISTS OF:
One Input Shaft
One Bearing Adapter
One Pin

NEEDS:
Installation on the vehicle

SPECS:
Length: 58mm (2.3")

Below is a wonderful product that numerous others have purchased the same time.

54T 0.8 P Spur Gear

This is the 54 Tooth Spur Gear
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Nylon construction
Black in color
.8 Module pitch

CONSISTS OF:
One 54T 0.8 Pitch Spur Gear

NEEDS:
Assembly onto vehicle

Regularly purchased with the product that you are presently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Externally size: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful product that numerous others have purchased the same time.

Cover, Gear (Clear)

This is the optional Clear Gear Cover for use on the Traxxas Slash 4x4.
**Will not fit the Ultimate Slash LCG, for that Gear Cover, order TRAC7477.**

FEATURES:
Plastic construction
Clear in color

CONSISTS OF:
One Clear Gear Cover

NEEDS:
Installation on the vehicle

Below is an additional product that praises the product being discussed.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FEATURES:
6061-T6 anodized blue aluminum construction
Steel 10x15x4mm ball bearing with blue rubber seal
Used on slipper shaft

CONSISTS OF:
One aluminum adapter
One 10x15x4mm ball bearing

NEEDS:
Installation on to slipper shaft
Remaining clutch pieces

The listed below product additionally sets actually well with the product being discussed.

Drive Hub, Center, Rear (1)/ F

This is the Front and Rear Center Drive Hub Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel construction

CONSISTS OF:
One Front Center Drive Hub
One Rear Center Drive Hub
One Screw Pin

NEEDS:
Installation in drive assembly

Below is a wonderful product that numerous others have purchased the same time.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one required).

This product is often purchased with the above discussed product.

12 X 18 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

    These are the replacement Wheel Hub Ball Bearings for
the Traxxas Nitro Revo Monster Truck.

FEATURES:
Stainless Steel Construction
Blue Rubber Sealed

CONSISTS OF:
Two 12mm x 18mm Blue Sealed Stainless Wheel Hub Bearings

NEEDS:
Assembly onto Car

SPECS:
Outer Size: 18mm (0.70")
Inner Size: 12mm (0.47")
Thickness: 4mm (0.15")

COMMENTS:
These are for the Within the Wheel Hubs, the Truck Requires
Four Total of these Bearings.