Traxxas Input Shaft/ Drive Gear Assemb

This is the replacement Input Shaft/Drive Gear Assembly for the
Traxxas 3905 E-Maxx Truck.

FEATURES:
Steel shaft, black in color
Steel drive gear assembly, silver in color

CONSISTS OF:
One Input Shaft with 18 Tooth Top Gear

NEEDS:
Installation following the design manual

SPECIFICATIONS:
Shaft Diameter: 5mm
Shaft Length: 3.53" (90mm)
Thread Size: 4mm

Get this product to improve the one you are reading around.

Output Shaft, Transmission

This is the Transmission Output Shaft for the Traxxas E-Maxx.

FEATURES:
Metal building and construction, black in color

CONSISTS OF:
One transmission output shaft, Part #5369

NEEDS:
Installation on the Traxxas E-Maxx

SPECIFICATIONS:
General length: 2.75" (70mm)
Diameter of drive canine install: .39" (10mm)
Diameter of shaft: .23" (6mm)

Right here is a fantastic product that many others have actually purchased the very same time.

Output Gear, 33 T W/ Spacers (

This is the Output Gear 33T for the Traxxas E-Maxx Truck.

FEATURES:
Black nylon building and construction

CONSISTS OF:
One 33T output gear
2 spacers

NEEDS:
Silicone Grease, usage TRAC6037

SPECIFICATIONS:
External size: 1.37" (35mm)
Thickness: 1.02" (26mm)

This product is frequently purchased with the above discussed product.

Gearbox Halves, Shift Detent B

These are the replacement Gearbox Halves for the Traxxas E-Maxx Truck.

FEATURES:
Black plastic building and construction

CONSISTS OF:
Gearbox halves (front and rear) and screws

NEEDS:
Remainder of the gearbox contents

SPECIFICATIONS:
Length: 2.67 (68mm) (at largest point)
Width: 3.42" (87mm) (at largest point)

Lots of others have actually purchased this product together with the product that you are currently reading about.

Idler Gear, 20-Tooth/ Idler Ge

This is the replacement 20 Tooth Idler Gear and Shaft for the
Traxxas E-Maxx 4WD RTR.

FEATURES:
Steel building and construction, weapon metal in color
Replaces a worn or damaged idler gear and shaft

CONSISTS OF:
One 20 Tooth Idler Gear
One 5x18mm Idler Gear Shaft

NEEDS:
Installation following the design manual

SPECIFICATIONS:
Externally Diameter: .86" (22mm)
Inside Diameter: .43" (11mm)
Thickness: .50" (12.5mm)

Right here is a fantastic product that many others have actually purchased the very same time.

Motor Plate For Single Motor

This is the optional Single Motor Plate for the
Traxxas E-Maxx 16.8V RTR.

FEATURES:
Aluminum building and construction, blue in color
Developed for a clean set up of a single brushless motor system in
the E-Maxx 16.8V RTR (requires gear cover number TRAC3997)

CONSISTS OF:
One Aluminum Motor Plate

NEEDS:
Installation and motor cover number TRAC3997

You will enjoy this product if you have the product just above pointed out.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Externally size: 7/16" (11mm)
Width: 5/32" (4mm)

This product compliments the above reviewed product.

6 X 12 X 4Mm Ball Bearing (2) Blue Rubber Sheild R Evo

This is a 6X12mm Ball Bearing Set from Traxxas.

FEATURES:
Steel building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) ball bearings, Part #5117

SPECIFICATIONS:
Inside size: 6mm
Externally size: 12mm
Width: 4mm

COMMENTS:
This bearing set is utilized in the transmission and differentials of
    the Revo.