Traxxas Housings, Differential, Front

This is the Front Differential Housing for the Traxxas Slash 4x4.

FUNCTIONS:
Solidified plastic building
Black in color

CONSISTS OF:
Two front differential housing halves

REQUIRES:
Setup around assembled differential components

Many others have purchased this thing in addition to the thing that you are presently reviewing.

Housings, Differential, Rear

This is the Back Differential Housing for the Traxxas Slash 4x4.

FUNCTIONS:
Solidified plastic building
Black in color

CONSISTS OF:
Two rear differential housing halves

REQUIRES:
Setup around diff components

Many others have purchased this thing in addition to the thing that you are presently reviewing.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful thing that lots of others have bought at the same time.

8 X 16 X 5Mm Ball Bearing (2) Blue Rubber Sheild R Evo

    These are the replacement Differential Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Construction
Blue Rubber Sealed

CONSISTS OF:
Two 8mm x 16mm Rubber Sealed Bearings

REQUIRES:
Assembly onto Car

SPECS:
Inner Diameter: 8mm (0.31")
Outer Diameter: 16mm (0.62")
Thickness: 5mm (0.19")

This thing praises the main item below.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

REQUIRES:
Assembly to car

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are utilized to support the Primary Clutch (one required).

This thing praises the main item below.

Suspension Pin Set, Complete Frt & Rr Includes Frt & Rr Swa

This is the Suspension Pin Set for the Traxxas Slash 4X4.
The hinge pins hold the suspension arms to the bulkheads

FUNCTIONS:
Long lasting steel building
Silver in color

CONSISTS OF:
Four 51.5mm pins
Four 30mm pins

REQUIRES:
Setup on the Slash 4x4

This is a great addition to the thing presently being discussed.

Front Bulkhead For Slash 4X4 Lcg And Rustler 4X4, Black

This is the optional RPM Front Bulkhead for the Traxxas Slash LGC 4x4.
**Suitable with the LGC chassis just**
**will not deal with the standard chassis version of the Slash 4x4.**

FUNCTIONS:
Two-piece design enables front end of car to be removed without
    needing to remove the bellcranks
Side dirt guards blend with the chassis and assistance secure the
    guiding servo and bellcrank area from dirt
Constructed of engineering grade nylons, black in color

CONSISTS OF:
Two-Piece Front Bulkhead with Installing Hardware and Instruction Sheet

This thing praises the above discussed thing.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Hub for use on the Traxxas Slash 4x4.

FUNCTIONS:
Solidified steel building

CONSISTS OF:
One Drive Hub
One Screw Pin

REQUIRES:
Setup on the car

SPECS:
Length: 19mm (0.75")
Diameter: 12mm (0.47")

This thing praises the main item below.

Motor Titan 12T 550 (12-Turns)

    This is the Traxxas Titan 550 12 Turn Electric Motor.

FEATURES:
Stock motor provided with the Traxxas Stampede and Rustler series
Preinstalled leads, capacitors and ports

CONSISTS OF:
Traxxas Titan 550 Motor, two capacitors and two leads with ports

REQUIRES:
Installing in car

SPECS:
Can Diameter: 1.25" (38mm)
Shaft Diameter: 0.12" (3mm)
Length Including Shaft: 3.2" (81mm)
Length Not Including Shaft: 2.3" (57.5mm)
Specs such as RPM are not offered