Traxxas Housings, Differential, Front

This is the Front Differential Housing for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic building and construction
Black in color

INCLUDES:
Two front differential housing halves

REQUIRES:
Setup around put together differential components

Several others have bought this thing along with the thing that you are currently reading about.

Housings, Differential, Rear

This is the Rear Differential Housing for the Traxxas Slash 4x4.

FEATURES:
Hardened plastic building and construction
Black in color

INCLUDES:
Two rear differential housing halves

REQUIRES:
Setup around diff components

Several others have bought this thing along with the thing that you are currently reading about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Below is a wonderful thing that several others have purchased the same time.

8 X 16 X 5Mm Ball Bearing (2) Blue Rubber Sheild R Evo

    These are the replacement Differential Bearings for
the Traxxas Nitro Revo Beast Truck.

FEATURES:
Stainless Building and construction
Blue Rubber Sealed

INCLUDES:
Two 8mm x 16mm Rubber Sealed Bearings

REQUIRES:
Assembly onto Automobile

SPECS:
Inner Diameter: 8mm (0.31")
Outer Diameter: 16mm (0.62")
Thickness: 5mm (0.19")

This thing compliments the main item right here.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Shielded with blue rubber seals

INCLUDES:
Two Ball Bearings

REQUIRES:
Assembly to car

SPECS:
Inner Diameter: 10mm
Outer Diameter: 15mm
Side Thickness: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one required).

This thing compliments the main item right here.

Suspension Pin Set, Complete Frt & Rr Includes Frt & Rr Swa

This is the Suspension Pin Set for the Traxxas Slash 4X4.
The hinge pins hold the suspension arms to the bulkheads

FEATURES:
Resilient steel building and construction
Silver in color

INCLUDES:
4 51.5mm pins
4 30mm pins

REQUIRES:
Setup on the Slash 4x4

This is a amazing enhancement to the thing currently being talked about.

Front Bulkhead For Slash 4X4 Lcg And Rustler 4X4, Black

This is the optional RPM Front Bulkhead for the Traxxas Slash LGC 4x4.
**Suitable with the LGC chassis only**
**will not deal with the standard chassis version of the Slash 4x4.**

FEATURES:
Two-piece design permits front end of car to be eliminated without
    having to get rid of the bellcranks
Side dirt guards blend with the chassis and assistance protect the
    guiding servo and bellcrank area from dirt
Constructed of engineering grade nylons, black in color

INCLUDES:
Two-Piece Front Bulkhead with Installing Hardware and Guideline Sheet

This thing compliments the above talked about thing.

Drive Hub, Frt, Hardened Steel (1) Screw Pin, (1) Fits Slash

This is the Front Hardened Steel Drive Hub for use on the Traxxas Slash 4x4.

FEATURES:
Hardened steel building and construction

INCLUDES:
One Drive Hub
One Screw Pin

REQUIRES:
Setup on the car

SPECS:
Length: 19mm (0.75")
Diameter: 12mm (0.47")

This thing compliments the main item right here.

Motor Titan 12T 550 (12-Turns)

    This is the Traxxas Titan 550 12 Turn Electric Motor.

FEATURES:
Stock motor provided with the Traxxas Stampede and Rustler series
Preinstalled leads, capacitors and ports

INCLUDES:
Traxxas Titan 550 Motor, two capacitors and two leads with ports

REQUIRES:
Setting up in car

SPECS:
Can Diameter: 1.25" (38mm)
Shaft Diameter: 0.12" (3mm)
Length Including Shaft: 3.2" (81mm)
Length Not Including Shaft: 2.3" (57.5mm)
Specs such as RPM are not offered