Traxxas Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Center Set for the Traxxas Rustler and
Stampede. These parts have actually more offset than
the stock hex wheel center set (TRAC6044).

FEATURES:
Gray plastic building

INCLUDES:
Two wheel centers
Two 2.5mmX12mm axle pins

SPECIFICATIONS:
Hex size: 12mm
Width: .32" (8mm)

Below is a terrific item that many others have bought at the exact same time.

Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that connect the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Numerous others have acquired this item in addition to the item that you are presently checking out.

Front Axles (2) (R & S)

This is a Set of Stock Replacement Front Axles for the Rustler and Stampede.
These are situated in the front steering blocks.

FEATURES:
Steel building
Natural color

INCLUDES:
Two front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Diameter: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

This is a fantastic enhancement to the item presently being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

You will certainly love this product if you have the product previously mentioned.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on car

Below is one more item that praises the item being talked about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

This item praises the above talked about item.

Steering Blocks L&R Slash/ Rustler/Stampede/Bandit

These are the Left and Right Steering Blocks
for the Traxxas Bandit, Stampede and Rustler VXL series.

FEATURES:
Plastic building
Black in color

INCLUDES:
One left and best steering obstructs

NEEDS:
5x11x4mm bearings (DTXC1547)

Numerous others have acquired this item in addition to the item that you are presently checking out.

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building

INCLUDES:
Eiqht 4mm flanged nylon locking nuts

SPECIFICATIONS:
Outside diameter: 7mm

Below is one more item that praises the item being talked about.

Oilite Bushings 5X11mm

This is a replacement bushing set for the TRAXXAS TRX-10 BULLET, HAWK2, and
different other TRAXXAS SETS. .
FEATURES:
Made of metal

INCLUDES:
14 bushings

SPECIFICATIONS:
5x11mm bushings

REMARKS:
These bushings would deal with any car utilizing 5x11mm bushings.

This item praises the main item right here.

Large Servo Saver

This is a big servo saver that can be used in Traxxas automobiles or any automobile that
requires a big design servo saver.
FEATURES:
Tough white plastic construction.
INCLUDES:
1 large servo saver and 3 adaptors that enable you to install the saver
on the majority of popular servos consisting of: Futaba, Hobbico, Tower, Airtronics,
and Traxxas. Also consisted of is an installing screw.
SPECIFICATIONS:
Length: 1-3/8"
Diameter: 1"
The servo saver has 6 holes for installing the guiding linkages.