Traxxas Hex Hubs & Axle Pins Slash

These are the replacement rear wheel adapters for the Hawk, Hawk 2, Bullet,
Sledgehammer, Eagle, and Blue Eagle LS. These are hex nuts that link the
rear wheels to the axles.

INCLUDES:
2- plastic hex collars (wheel adapters)
4- stub axle pins

WAJ
1/16/93

Want an additional fantastic item to enhance the above stated item?

4Mm Flanged Nylock Nuts (8)

This is the Traxxas Flanged Nylon Locking Nuts.

FEATURES:
Steel serrated building

CONSISTS OF:
Eiqht 4mm flanged nylon locking nuts

SPECS:
Outdoors diameter: 7mm

This item is often gotten with the above stated item.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

The listed below item also sets actually well with the item being discussed.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

This item praises the main item here.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on automobile

Often gotten with the item that you are presently reading about.

Hex Wheel Hub 2.5 X 12Mm Rustler / Stampede / Slash

This is a Hex Wheel Hub Set for the Traxxas Rustler and
Stampede. These parts have actually more balanced out than
the stock hex wheel center set (TRAC6044).

FEATURES:
Gray plastic building

CONSISTS OF:
Two wheel centers
Two 2.5mmX12mm axle pins

SPECS:
Hex size: 12mm
Width: .32" (8mm)

This is a amazing addition to the item presently being discussed.

Front Axles (2) (R & S)

This is a Pair of Stock Replacement Front Axles for the Rustler and Stampede.
These are located in the front steering blocks.

FEATURES:
Steel building
Natural color

CONSISTS OF:
Two front axles

NEEDS:
Nothing. These are direct replacement parts.

SPECS:
Length: 32mm (1.26")
Size: 5mm

REMARKS:
These will not work for the nitro variations. For that axle, use
    TRAC2536.

Many others have gotten this item together with the item that you are presently reading about.

4Mm Alum Flanged Nylock Nuts Blue (4)

These are the 4mm Flanged Nylon Locknuts from Traxxas.

FEATURES:
Aluminum building anodized blue in color
Serrated on the back for sure grip

CONSISTS OF:
Four 4mm Flanged Nylon Locknuts

NEEDS:
6mm nut driver

SPECS:
Hole Size: 4mm
Hex Size: 6mm

Right here is an additional item that praises the item being discussed.

39Mm Camber Link Turnbuckles (Fr) Slash, Bandit, Stampede

These are the 39mm Turnbuckle Camber Links
for the Traxxas Stampede and Rustler VXL.

FEATURES:
Metal and Nylon Building and construction
Silver and Black in Color
Put together w/Rod Ends

CONSISTS OF:
Two front 39mm (69mm center to center) turnbuckles and guideline
    sheet

NEEDS:
Installation on the automobile

Often gotten with the item that you are presently reading about.

3 X 15Mm Button Hex Screw (6)

This is a package of 6 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel building, Black in color
Used on the Traxxas Revo beast truck, can also be utilized in any
    application where a 3x15mm button head screw is required

CONSISTS OF:
6 3x15mm Traxxas Button Head Screws

NEEDS:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Size: 3mm