Traxxas Gearbox Halves L&R Grey

This is a Left and Right Gearbox half with Idler Shaft for the
Traxxas Stampede and Traxxas Rustler.

FEATURES:
Gray plastic building and construction
Steel idler shaft

INCLUDES:
One gearbox
One idler shaft

COMMENTS:
This part fit the requirement and XL variation of both the Stampede
and Rustler.

This item praises the above gone over item.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Several others have actually gotten this item along with the item that you are presently reading about.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Below is one more item that praises the item being gone over.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

INCLUDES:
Main differential with steel ring gear
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Installation on the car

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037

This item praises the main item here.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

The listed below item also sets really well with the item being gone over.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

INCLUDES:
Rear driveshaft assembly
Screw pin

NEEDS:
Installation on car

This is a superb addition to the item presently being gone over.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits a number of Traxxas
vehicles. .
Consists of: 1 gear just

You will enjoy this product if you have the product previously mentioned.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on car

Want one more excellent item to match the above stated item?

Stub Axle Pins (4)

These are replacement stub axle pins for the Nitro Buggy, Nitro Street, TRX-3,
Rad 2, TRX-1, Hawk 2, and Blue Eagle LS II. These pins slide through the axle
and hold the wheel to the axle.

INCLUDES:
4- stub axle pins

WAJ
1/30/94

This is a superb addition to the item presently being gone over.

Dust Cover/ Rubber Plug

This is a Dust Cover and Rubber Plug
for the Traxxas Rustler/Stampede

FEATURES:
Made from black molded nylon
For the Traxxas Rustler/Stampede

INCLUDES:
Dust cover for the Traxxa Rustler
3 x 6 mm round head coarse thread screws (to mount dust cover)
Rubber Plug

Specifications: 3" (77mm)
Compatible with Traxxas Telemetry